563932
15
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
15
VQT4Z19
Others
1
Press [SETUP] to select “Dimmer”.
2 Press [2, 1] to select “On” and then press [OK].
Note:
To cancel, select “Off” in step 2.
This function switches off the system (except in radio
source) if you do not use the system for approximately
20 minutes.
1 Press [SETUP] repeatedly to select “Auto Off”.
2 Press [2, 1] to select “On” and then press [OK].
Note:
To cancel, select “Off” in step 2.
When connected to a Bluetooth
®
device, this function does
not work.
If “Net Standby” is set to “On”, this function will also be set
to “On”. To change the setting, set “Net Standby” to “Off”.
(> right)
Occasionally, Panasonic may release updated software
for this system that may add or improve the way a
feature operates. These updates are available free of
charge.
Preparation
Turn this system on.
Connect this system to the home network. (> 6)
Make sure that the network is connected to the
Internet.
If “D.Connect” is set to “On”, change the setting to
“Off” and connect this system to a network that is
connected to the Internet.
1 Press [SETUP] repeatedly to select “SW Update”
and then press [OK].
2 Press [2, 1] to select “Update? Yes” and then
press [OK] to start the update.
Select “Update? No” to cancel the update.
{. After the update has finished, “Success” is displayed.
3 Disconnect the AC mains lead and reconnect it
after 3 minutes.
If there are no updates, “No Need” is displayed.
Downloading will require several minutes. It may take
longer or may not work properly depending on the
connection environment.
Checking the software version
1 Press [SETUP] repeatedly to select “SW Version” and
then press [OK].
{. The version of the installed software is displayed.
2 Press [OK] to exit.
To check the Wi-Fi signal strength where this system is
located.
Preparation
Connect this system to the wireless network. (> 6)
1 Press [SETUP] repeatedly to select “Signal
Level” and then press [OK].
This system’s displays show “Level ”.
(“ ” stands for a number.)
2 Press [OK] to exit this display mode.
It is recommended to have a signal strength of “3”. Change
the position or angle of your wireless network router or this
system if the indication is “2” or “1” and see if the
connection improves.
If “Level 0” is displayed, this system cannot establish a link
with the wireless network router. (> 17)
This function does not work when “D.Connect” is set to
“On”.
The wireless LAN function can be enabled or disabled.
1 Press [SETUP] repeatedly to select
“Wireless LAN” and then press [OK].
2 Press [2, 1] to select “On” or “Off” and then
press [OK].
The factory preset is “On”.
This system can turn on automatically from standby mode
when this system is selected as the AirPlay speakers.
Preparation
Connect this system to the home network. (> 6)
1 Press [SETUP] repeatedly to select
“Net Standby” and then press [OK].
2 Press [2, 1] to select “On” and then press [OK].
To cancel this function, select “Off” in step 2.
The factory preset is “Off”. If this function is set to “On” the
standby power consumption will increase.
Display the name for the connected wireless network
(SSID).
1 Press [SETUP] repeatedly to select “Net Info”
and then press [OK].
“IP Addr.” is indicated on the display.
2 Press [SETUP] repeatedly to select “SSID” and
then press [OK].
3 Press [OK] to exit.
If “No Connect” is displayed this system is not connected to
a wireless network.
All letters are displayed as capital letters, and characters
that cannot be displayed are replaced with “
¢”.
To check this system’s IP address or the Wi-Fi MAC address.
1 Press [SETUP] repeatedly to select “Net Info”
and then press [OK].
“IP Addr.” is indicated on the display.
2 Press [SETUP] repeatedly to select “IP Addr.” or
“MAC Addr.”and then press [OK].
The IP address or the MAC address is partially
displayed.
3 Press [2, 1] on the remote control to show the
rest of the IP address or the MAC address.
To exit the setting, wait 20 sec.
The “ – ” displayed on the top or bottom left of the display
indicate the first and last units respectively.
Decrease the brightness of the display panel
Automatically switch off the system
Software update
DO NOT DISCONNECT the AC mains lead while
one of the following messages is displayed.
“Linking”, “Updating” or “%”
(“ ” stands for a number.)
During the update process, no other operations can be
performed.
Wi-Fi signal strength
Wireless LAN setting
Network standby
Wireless network name (SSID)
IP/MAC Address
SC-PMX9-VQT4Z19.book 15 ページ 2013年3月21日 木曜日 午後4時16分
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Panasonic SC-PMX9DB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Panasonic SC-PMX9DB in de taal/talen: Engels als bijlage per email.

De handleiding is 1,96 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Panasonic SC-PMX9DB

Panasonic SC-PMX9DB Gebruiksaanwijzing - Nederlands - 84 pagina's

Panasonic SC-PMX9DB Snelstart handleiding - Nederlands - 1 pagina's

Panasonic SC-PMX9DB Snelstart handleiding - Deutsch - 1 pagina's

Panasonic SC-PMX9DB Gebruiksaanwijzing - Deutsch - 84 pagina's

Panasonic SC-PMX9DB Snelstart handleiding - English - 1 pagina's

Panasonic SC-PMX9DB Snelstart handleiding - Français - 1 pagina's

Panasonic SC-PMX9DB Gebruiksaanwijzing - Français - 84 pagina's

Panasonic SC-PMX9DB Snelstart handleiding - Italiano - 1 pagina's

Panasonic SC-PMX9DB Gebruiksaanwijzing - Italiano - 84 pagina's

Panasonic SC-PMX9DB Gebruiksaanwijzing - Dansk - 64 pagina's

Panasonic SC-PMX9DB Snelstart handleiding - Dansk - 1 pagina's

Panasonic SC-PMX9DB Snelstart handleiding - Svenska - 1 pagina's

Panasonic SC-PMX9DB Gebruiksaanwijzing - Svenska - 64 pagina's

Panasonic SC-PMX9DB Snelstart handleiding - Suomi - 1 pagina's

Panasonic SC-PMX9DB Gebruiksaanwijzing - Suomi - 64 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info