640535
5
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
4
EN
22. CHECKING THE GRINDING WHEEL SHAPE
- With the machine turned off, check the grinding wheel prole using the dedicated
template (g.17); if necessary, dress the wheel to restore the correct prole.
23. GRINDING WHEEL DRESSING
Wear personal protection equipment.
- Start the grinder by turning the switch to position “1”.
- Once started, the lamp lights up to illuminate the sharpening area.
- Prole the grinding wheel with the dressing brick, always working with extreme
caution, holding it with two hands rmly and effectively (g.18).
- Stop the machine and check if the prole is correct using the template (g.19).
Contact with the grinding wheel while it spins at high speed may cause
burning and abrasions.
24. ADJUSTING THE GRINDER
24.1 SHARPENING ANGLES
- Once you have established the type of chain to be sharpened, look-up the adjust-
ment angles (vise and arm) in the chain chart (columns A/B/C).
RH CUTTER
24.2 SETTING THE TOP SHARPENING ANGLE (FIG.20-21)
- Loosen the knob M20.
- Turn the vise clockwise.
- Position the “0” reference mark on the vise by the desired
angle.
- Tighten knob M20 again.
LH CUTTER
24.3 SETTING THE TOP SHARPENING ANGLE (FIG.20-22)
- Loosen the knob M20.
- Turn the vise counter clockwise.
- Position the “0” reference mark on the vise by the desired
angle.
- Tighten knob M20 again.
24.4 SETTING THE CUTTING ANGLE (FIG.23)
(right and left cutters)
- Loosen the knob at the back M23 and turn the arm towards the
right. Position the “0” reference mark by the angle desired.
- Tighten knob M23 again.
24.5 SHARPENING ANGLES FOR CHAINS WITH “DOWN ANGLE”
- Find the setting angles as just illustrated.
- Set another sharpening position: the down angle. To nd out which chains require
this setting, consult column B in the chain chart.
Down Angle
RH CUTTER
24.6 SETTING THE DOWN ANGLE (FIG.25)
- Loosen knob M20.
- Swing the vise right inwards until the left reference mark
matches that underneath.
24.7 SETTING THE TOP SHARPENING ANGLE (FIG.26)
- Turn the vise clockwise.
- Position the “DOWN 10” reference mark (right) of the vise by
the desired angle.
- Tighten knob M20 again.
Down Angle
LH CUTTER
24.8 SETTING THE DOWN ANGLE (FIG.27)
- Loosen knob M20.
- Swing the vise right towards the operator so that the right
reference mark matches that underneath.
24.9 SETTING THE TOP SHARPENING ANGLE (FIG.28)
- Turn the vise counter clockwise.
- Position the “DOWN 10” reference mark (left) of the vise by
the angle desired.
- Tighten knob M20 again.
Down Angle
24.10 SETTING THE CUTTING ANGLE (FIG.24)
(right and left cutters)
- Loosen the handle at the back M23 and turn the arm towards
the right. Position the “DOWN 10” reference mark on the
angle desired.
- Tighten knob M23 again.
24.11 SETTING THE CHAIN BLOCKING UNIT (FIG.29)
- Put the chain in the vise.
- Take the cutter up against the chain blocking device A29.
- Turn the knob P29 to position the blocking unit A29 correctly compared to the
cutter.
24.12 POSITIONING THE CUTTER
- Tighten the pin P17, to release the arm (g.22).
- Move the grinding wheel onto the cutter to be sharpened by pulling the arm
downwards.
- Turn the knob P30 to move the chain so that the cutter cutting edge skims the
grinding wheel (g.30). The chain should run freely over the vise throughout this
procedure but without any clearance.
- At this stage, raise the arm and screw the knob P30, to move the cutter to be
sharpened further forwards.
This forward movement corresponds to the quantity of material to be ground
from the cutter.
Blunter the cutters, greater must be this forward movement. Vice versa, for cutters
that are not too blunt, simply grind just a slight amount of material.
- Turn knob P31 to adjust the cutter sharpening depth. The grinding wheel should
skim the bottom of the cutter vertically (g.31).
- Once you have found the exact position of the cutter, tighten the chain blocking
handle M32 (g.32).
Pull the handle M32 towards the operator to re-position it to facilitate the sharpening
process.
25. SHARPENING WARNINGS
- Wear personal protection equipment when sharpening.
- All adjustments must be made with the motor switched off and the grinding
wheel completely stopped.
- In the case of accidental impact or collision of the wheel during the shar-
pening process, follow the instructions given in the “GRINDING WHEEL
WARNINGS” section.
- Clean the chain before sharpening it.
- To avoid overloading the motor excessively and to avoid damaging the chain cut-
ters , grind minimum quantities of material and do not stop along the same cutter
as this could burn the cutting edge.
- Sharpen all the cutters on the same side and then adjust the vise as explained in
the previous sections, then sharpen the cutters on the opposite side.
- Do not use cooling liquids during the sharpening process.
26. SHARPENING THE CHAIN
- Make sure the vise blocking handle M32 is screwed tight and the chain is
blocked.
- Turn the machine on using switch I33 and sharpen the cutter by lowering the arm-
motor unit (g.33).
- Once you have sharpened the chain, raise the arm and loosen the handle M32.
- Run the chain forward to position the next cutter to be sharpened.
- Block again with the handle M32 and sharpen.
27. GRINDING WHEEL WEAR COMPENSATION
- When the wheel diameter wears down and reaches a dimension within zone A on
the shield guard (g.34), you need to re-position the vise assembly.
This will improve the working conditions of the grinder.
- Loosen the securing screws V35 (g.27).
- Move the vise assembly towards the right until the reference “A” matches the refer-
ence mark on the vise itself (g.28).
- Tighten the securing screws V35.
This will maintain the ideal working conditions of the grinder.
- Loosen the securing screws V35 (g.35).
- Move the vise assembly towards the right until reference Amatches the reference
mark on the vise itself (g.36).
- Tighten the securing screws V35.
28. GRINDING WHEEL DRESSING FOR SHARPENING THE DEPTH
GAUGE
- Fit the 5/16” (8 mm) thick grinding wheel (g.37), following the instructions given
in points 13-17-18-19.
- Turn the vise so that the “0” reference mark is on position 0 (g.38).
- Turn the arm to take the “0” reference mark to 10°/15° (g.38).
- Position the dressing brick on the jaws and against the chain blocking unit
(g.38).
Hold the dressing brick rmly with one hand (being careful not to touch the
grinding wheel).
- Prole the grinding wheel by activating the machine and grind the grinding wheel
until you obtain a prole like the one illustrated in g.38.
- Switch the machine off once you have nished.
29. SHARPENING THE DEPTH GAUGE
- Remove the dressing brick and put the chain in the vise.
- Center the cutter compared to the grinding wheel by turning the knobs (P29 and P30).
- Keeping the arm tilted, adjust the grinding depth on the gauge by turning knob P31
(g.39).
- Sharpen the gauge following the instructions given in the “SHARPENING” section.
For this type of sharpening procedure, there is no difference between the right and
left cutters, therefore sharpen all the gauges one after the other.
P00801046_R05_511AX.indd 4 12/06/2009 9.02.14
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Oregon 511AX bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Oregon 511AX in de taal/talen: Engels als bijlage per email.

De handleiding is 4,08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info