618128
6
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
6
PAD MODE COMMANDS
The lower row of pads has different functions depending on their mode: Looping Mode, Sample Mode, or Hot
Cue Mode.
To select a mode, hold down the SHIFT button and press one of the lower pads. An LED under
the pad section indicates the currently selected mode.
Looping Mode: Press Shift + Loop In to assign the lower 4 pads to the functions listed below:
Loop In Sets the beginning of a loop. After a Loop Out point is set, when this button is pressed again, it
will allow for fine adjustment of the Loop In point.
Loop Out – Sets the end point for the loop. When this button has been pressed after a Loop Out point has
been set, it will allow for fine adjustment of the Loop Out point.
Reloop – When this is pressed inside a loop, this will turn the loop off. When pressed outside a loop, this
will activate the loop and start playback from its Loop In point. If a loop has not been set, this button will
have no effect.
Loop x1/2 – Cuts the currently playing loop in half. Press Shift + Loop x1/2 to double the length the
currently playing loop.
Sample Mode: Press Shift + Loop Out to assign the lower 4 pads to the functions listed below:
Sample 1 (S1) – Plays the sample assigned to Sample Pad 1.
Sample 2 (S2) – Plays the sample assigned to Sample Pad 2.
Sample 3 (S3) – Plays the sample assigned to Sample Pad 3.
Sample 4 (S4) – Plays the sample assigned to Sample Pad 4.
Hot Cue Mode: Press Shift + Reloop to assign the lower 4 pads to the functions listed below:
Cue 1 (C1) – If a cue point has not already been set for the loaded track, this control will mark Cue Point
1. If a cue point has already been set, this control will jump to Cue Point 1.
Cue 2 (C2) – If a cue point has not already been placed on the loaded track, this control will mark Cue
Point 2. If a cue point has already been set, this control will jump to Cue Point 2.
Cue 3 (C3) – If a cue point has not already been placed on the loaded track, this control will mark Cue
Point 3. If a cue point has already been set, this control will jump to Cue Point 3.
Delete Cue (C) – Press this button, and then press one of the other pads in the row to delete its cue point.
SIDE PANEL
1. Headphone Output – Connect headphones to these 1/4”
and 1/8” jacks for monitoring the signal. The headphone
volume is controlled using the Cue Gain knob.
2. Microphone Input – Connect a standard dynamic
microphone to this 1/4” jack.
3. Mic Gain Adjusts the level for the microphone input.
REAR PANEL
1. Master Output (RCA) – Use standard RCA cables to connect
this output to a speaker or amplifier system.
2. USB – Sends USB MIDI data to control various software
parameters.
1
2
2
3
1
1
2
2
3
1
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Numark Mixtrack Pro II bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Numark Mixtrack Pro II in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 7,45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info