167884
4
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
X1000D - amplifier owner's manual
4
Installation & Mounting
Any deviation from the connection specifications recommended may cause serious damage to the amplifier, spea-
kers and/or vehicle electrical system. Please double-check the connection before turning the system on.
1. Disconnect the vehicle’s negative battery connection.
2. Determine the mounting place for your MTX XTHUNDER amplifier. Keep in mind that there needs to be sufficient
air flow across the heatsink of the amplifier to ensure proper cooling. Mark the mounting holes of the amplifier and
drill the holes to mount your amplifier. Before drilling any holes make sure that all vehicle wires, gas lines, brake
lines, gastank etc. are clear and will not interfere with the installation. Mount your MTX XTHUNDER amplifier.
3. Run a positive power cable from the vehicle’s battery through the firewall using a grommet or firewall bushing to
avoid damage to the cable from sharp edges of the firewall. Run the cable through the interior of the vehicle and
connect the end to the amplifier’s +BATT terminal. Leave the cable disconnected from the battery.
Note : Use only proper gauge wire for both positive and negative connections for optimum performance.
4. Install a circuit breaker or fuse within 30cm of the battery. This effectively lowers the risk of severe damage to
you or your vehicle in case of a short circuit or accident. Make sure the circuitbreaker is switched off or the fuse is
taken out of the fuse holder untill all connections are made. Now connect your positive power cable to the positive
battery terminal of the battery
5. Find a good ground source on the vehicle’s chassis and remove the paint to reveal bare metal at the contact
point. Attach the ground wire to that contact point and connect the other end of the ground wire to the GND termi-
nal of your MTX XTHUNDER amplifier.
6. Connect a Remote Turn-on wire from your source unit to your MTX XTHUNDER amplifier’s Remote terminal. If
your source unit does not have a dedicated Remote Turn-on lead, you may connect to the source unit’s Power
Antenna lead.
7. Connect RCA cables from your source unit to your MTX XTHUNDER amplifier’s RCA input jacks. If RCA (low level)
output is not available, connect the included speaker (high level) connector to the speaker wires from the source
unit.
8. Connect your speakers to your MTX XTHUNDER amplifier’s speaker terminals using 4mm2 minimum speaker
cable.
9. Double-check all the previous installation steps, in particular, the wiring and component connections. If every-
thing is in order, reconnect the vehicle’s negative battery connection, switch your circuitbreaker on or place your
fuse in the fuse holder and begin adjusting your amplifier.
Note: Be sure that the Gain Level on the amplifier is turned all the way down (counter clockwise) before proceeding
with adjustments.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Mtx audio x1000d bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Mtx audio x1000d in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 1,73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info