167884
3
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
www.mtx.com - www.mtxaudio.eu
4. Input selection switch - This switch, is used to match the amplifier’s input to the source unit’s or DSP unit’s output.
If your source unit or DSP unit has a mono output you can select: Mono L or Mono R as your input connection,
if your source unit or DSP unit has a stereo output you need to select SUM for input now both RCA inputs of the
amplifier are active and the stereo signal will be converted into a mono signal by the amplifier.
5. EBC port - For connecting the included External Bass Control. A remote bass control so the bass can be adjusted
from the driver’s seat.
6. Subsonic filter control - This control is used to select the desired (high pass) subsonic filter frequency. The sub-
sonic filter protects the subwoofer(s) against too low frequencies that can dammage the subwoofer(s).
7. Low pass x-over frequency control - This control is used to select the desired low pass x-over frequency. The
frequency can be adjusted between 40Hz and 200Hz.
8. Speaker Terminals Be sure to observe speaker polarity through the system. Failing to wire the speakers in
proper phase could result in a loss of bass response and/or poor
overall sound quality.
Caution : The X1000D amplifier is not recommended for loads below 2 ohms.
9. Fuse - For convenience, all MTX XTHUNDER amplifiers utilize ATC type fuses. For continued protection in the
event that a fuse blows, replace the fuse only with the same value.
Caution : The power fuse on the amp is for protecting the amp against overdrive. To protect the vehicle’s electrical
system, an additional fuse is required within 30cm of the battery on the 12V+ cable.
10. Power Terminal – This is the main power input for the amplifier and must be connected directly to the positive
terminal of the car battery for the amplifier to operate properly. Use caution when running this cable through the
vehicule. Try to avoid running this cable along side the input RCA cables, antenna cabling, or other sensitive equi-
pment as the large amount of current flowing through this cable can induce noise into your system. It is also very
important to have a tight connection to ensure maximum performance. We recommend to use 10mm2 or larger
power wire with the MTX XTHUNDER X1000D amplifier.
11. Remote Terminal – The Amplifier can be turned on by applying 12 volts to this terminal. Typically this voltage is
supplied by a wire from the source unit marked “remote” or “electric antenna”.
12. Ground Terminal – A good quality ground is required for your Amplifier to operate at peak performance. A short
length of cable the same gauge as your power cable should be used to attach the ground terminal directly to the
chassis of the vehicle. Always scrape or sand any painted surfaces to expose bare metal where the ground wire
will attach.
3
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Mtx audio x1000d bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Mtx audio x1000d in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 1,73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info