168702
5
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
Installation & Mounting
MTX recommends your new Thunder amplier be installed by an Autho-
rized MTX retailer. Any deviation from specied installation instructions
can cause serious damage to the amplier, speakers and/or vehicles elec-
trical system. Damage caused from improper installation is NOT covered
under warranty. Please verify all connections prior to system turn on !
1. Disconnect the vehicle’s negative battery cable.
2. Determine the mounting place for your MTX THUNDER amplier. Keep in mind there should be sucient air ow for
proper cooling. Mark the mounting holes from the amplier to be drilled. Before drilling make sure all vehicle wires, gas
lines, brake lines and gas tank are clear and will not interfere with installation. Drill the desired holes and mount the MTX
THUNDER amplier.
3. Install a positive (+) power cable from the vehicle’s battery through the rewall using a grommet or rewall bushing to
avoid cable damage from sharp edges of the rewall. Run the cable through the interior of the vehicle and connect it to
the amplier’s +BATT terminal. Do Not connect to the battery at this time.
Note : Use only proper gauge wire for both positive and negative connections.
4. Install a circuit breaker or fuse within 20cm of the battery. This eectively lowers the risk of severe damage to you or
your vehicle in case of a short circuit or accident. Make sure the circuitbreaker is switched o or the fuse is taken out of
the fuse holder untill all connections are made. Now connect your positive power cable to the positive battery terminal
of the battery.
5. Grounding - Locate a proper ground point on the vehicle’s chassis and remove all paint, dirt or debris to reveal a bare
metal surface. Attach the ground wire to that contact point. Connect the opposite end of the ground wire to the GND
terminal on the MTX THUNDER amplier.
6. Connect a Remote Turn-on wire from the source unit to the MTX THUNDER amplier’s Remote terminal. If the source
unit does not have a dedicated Remote Turn-on lead, you may connect to the source unit’s Power Antenna lead.
7. Connect RCA cables from the source unit to the MTX THUNDER amplier’s RCA Bi-level inputs. Both low and high
level signals can be used. Run all signal cables away from vehicle wiring, computers and power cables. If cables must
be crossed do so at a 90° angle. Use only high quality twisted pair interconnect cables to decrease radiated noise from
entering the system.
• Using RCA Connections: Simply attach a signal cable from source units RCA outputs to the amps RCA inputs. This pro-
vides input signal to the amp.
• Using Speaker Level Connections : If the source unit does not have RCA outputs, high level signals can be used by tak-
ing the supplied high level RCA adapter and connecting it to the vehicle’s rear speaker wiring. Connect the left negative
speaker wire to the green and black striped wire on the high level RCA adapter. Connect the left positive speaker wire to
the solid green wire. Do the same for the right speaker connection using the purple wire. Now plug the RCA connectors
into the amps inputs.
8. Connect your speakers to the MTX THUNDER ampliers speaker terminals using proper gauge wire. The amp has two
PARALLEL speaker terminals, a positive and negative for a single woofer and an optional second set of positive and nega-
tive terminals for a two woofer conguration. The amp can drive a 1 ohm minimum load.
9. Double check all previous installation steps, in particular, wiring and component connections. Once veried, reconnect
the vehicle’s negative battery cable, turn the circuit breaker on or place the fuse in the fuse holder.
Note : Gain Levels on the amplier should be turned all the way down (counter clockwise) before proceeding with adjust-
ments.
Troubleshooting
Problem Cause Solution
No LED indication No +12V at remote connection Supply +12V to terminal
No +12V at Power connection Supply +12V to terminal
Insu cient ground connection Verify ground connection
Blown power fuse Replace fuse
Power LED on, no output Volume on source unit o Increase volume on source unit
Speaker connections not made Make speaker connections
Gain control on amplier o Turn up gain
Signal processing units o Apply power to signal processor
All speakers blown Replace speakers
Output distorted Head unit volume set too high Lower head unit volume
Amplier gain set too high Lower amplier gain
Balance reversed Speakers wired L + R reversed Wire speakers with correct orientation
RCA inputs reversed Reverse RCA input
Bass is weak Speakers wired out of phase Wire speakers with correct phase
Not using MTX woofers Buy MTX woofers
Blowing fuses Excessive output levels Lower the volume
Amplier defective Return for service
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Mtx audio th1500d bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Mtx audio th1500d in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 4,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info