168702
4
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
www.mtx.com - www.mtx.eu.com
Owners Manual - TH1500D
Speaker Terminals - Connect subwoofer(s) to these terminals. If using two subwoofers or a dual voice coil sub-
woofer, respect the phase.
Attention : The two (+) connectors are wired parallel internally. Same for the two (-) connectors.
Thermal Protection - This LED illuminates red when the amp reaches 100°C. The LED also turns red when the
power supply goes below 9V or over 16.2V.
Short Circuit Protection - This LED will ash yellow when the speaker outputs will short circuit. Without signal,
this LED can remain yellow when the speaker outputs are short circuited.
Fuses - When fuses blow, replace them with the same value. Never use a higher rated fuse !
(+12) Power Terminal - This is the main power input for the amplier and must be connected directly to the posi-
tive terminal of the vehicles battery for proper operation. Use caution when installing (+12) power cable in the
vehicle. Avoid running this cable parallel with RCA cables, antennas, or other sensitive equipment due to massive
currents that can induce noise into the audio system. It is also very important to have a tight, secure connection
for maximum performance. MTX recommends using 50mm
2
power wire with the MTX TH1500D amplier.
Remote Terminal – The amplier can be turned on by applying 12 volts to this terminal. Typically this voltage is
supplied by a wire from the source unit marked "remote" or "power antenna".
Ground Terminal A proper ground is required for your amplier to operate at peak performance. A short ground
cable the same diameter as the power cable should be used to attach the ground terminal directly to the chassis
of the vehicle. Always remove paint, dirt or debris to expose bare metal where the ground will be attached.
EBC Port (External Bass Control) - The Remote Subwoofer Level Control (EBC) plugs directly into this port, while
the EBC itself can be placed anywhere in the vehicle for on demand bass adjustments. EBC is included.
Master/Slave Switch - Used to put the amp in Master mode or Slave mode when bridging two TH1500D's. For
more details, see Master/Slave Mode section below.
Master/Slave Port - Used to connect two TH1500D when used in Master/Slave mode. The RJ15 cable is included.
For more detail see Master/Slave mode section below.
Master Slave Mode
For MAXIMUM output power, two TH1500D amps can be bridged together.
1. Decide which TH1500D is the "Master" amp. The other one will be the "Slave" amp. Set the "Bridge Mode"
switch (16) to "Master" on the master amp. Set the slave amp to "Slave" (16).
2. Connect the input signal from the source unit to the RCA inputs of the master amp. The slave amp doesn't
need RCA connection. It will take the signal from the master amp through the RJ15 cable.
3. Connect the included RJ15 cable to both amps.
4. Adjust the gain, x-over, subsonic lter and phase on the master amp. All slave amp controls are disconnected
through slave mode. The master amp fully manages the slave amp.
5. Your (+) speaker output is the (+) speaker output from the master amp.
6. Your (-) speaker output is the (+) speaker output from the slave amp.
Note: The EBC remote works ne in master/slave mode. It only needs to be connected it to the master amp.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Mtx audio th1500d bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Mtx audio th1500d in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 4,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info