588176
9
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
Connect Panel with Swing Motor Wire Connector (white) and Remote Controller Wire Connector
after passing through a hole. (Chart 18)
Hole
Swing Motor Wire
Chart 18 Swing Motor Wire
Swing Motor Wire
Installation Screws
Nut Cap
Chart 19 Installation sequence of screws
Confirm the wires are not nipped between the panel and the Indoor Unit, or the panel and the
ceiling. Then fasten the screws according to the following. (chart 19)
1) Fix the panel at central point temporarily.
2) Confirm and adjust the position.
3) Fix left side of panel (from to ) temporarily.
4) Fix right side of panel (from to ) temporarily.
5) Confirm the installation position.
6) Fasten the , , , , screws tightly.
After tightening Panel Screws, install two screw caps to the screws at side of Air Outlet. (chart 19 )
A
7
6
5
4
3
2
1
Lead Swing Motor Wire into a hole. (Chart 18)
Hang the Strip Hook of Inlet Grille to the hole in the middle of
Indoor Unit Air Inlet. (Chart 20)
Hole
Strip Hook
Chart 20 Hang the Strip Hook of Inlet Grille
NOTICES FOR BENDABLE PIPE
O
The bending angle should not exceed 90 .
Bending position is preferably in the bendable pipe. The larger the better it is.
Do not bend the pipe more than three times.
BEND THE CONNECTING PIPE OF SMALL WALL THICKNESS
Cut out a desired concave at the bending part of the insulating pipe. Then expose the pipe (cover
it with tapes after bending).
To prevent collapsing or deforming, please bend the pipe at its biggest radius.
Use bender to get a small radius pipes.
USE THE MARKET BRASS PIPE
Be sure to use the same insulating materials when you buy the brass pipe.
2. Locate The Pipe
Drill a hole in the wall (suitable just for the size of the wall conduit, 90mm in general), then set on the
fittings such as the wall conduit and its cover.
Bind the connecting pipe and the cables together tightly with binding tapes. Do not let air in, which
will cause water leakage by condensation.
Pass the bound connecting pipe through the wall conduit from outside. Be careful of the pipe
allocation to do no damage to the tubing.
Connect the pipes.
Then, open the stem of stop values of the outdoor unit to make the refrigerant pipe connecting the
indoor unit with the outdoor unit in fluent flow.
Be sure of no leakage by checking it with leak detector or soap water.
Cover the joint of the connecting pipe to the indoor unit with the soundproof / insulating sheath
(fittings), and bind it well with the tapes to prevent leakage.
3.
4.
5.
6.
1)
2)
3)
FLARING
90 +4
4
5
+
2
A
90
lean crude burr
Chart 28
Chart 29
Outside-
diameter
A (mm)
max
min
F6.35mm
F9.53mm
F12.7mm
8.7
12.4
15.8
8.3
12
15.4
1. Cut a pipe with a pipe cutter.
2. Insert a flare nut into a pipe and flare the pipe.
Table 1
EXPEL THE AIR
REFRIGERANT PIPE CONNECTING
FASTEN THE NUT
Put the connecting tubing at the proper position,
wrench the nuts with hands then fasten it with a
wrench. (Refer to Chart 30)
Chart 30
7
10
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Midea MCB12HRN2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Midea MCB12HRN2 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Midea MCB12HRN2

Midea MCB12HRN2 Installatiehandleiding - Nederlands - 5 pagina's

Midea MCB12HRN2 Gebruiksaanwijzing - Nederlands - 9 pagina's

Midea MCB12HRN2 Gebruiksaanwijzing - English - 22 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info