588176
7
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
Location of the ceiling hole and hanging screw bolts.
Panel Length 1050
Ceiling Hole Length 1010
Hanging Bolts Distance 890
Ceiling Hole Width 430
Panel Centre
Indoor Unit Size 400
Hanging Bolts
Distance
330
Indoor Unit size 850
Panel Width 470
20
395
455
110
20
20
50
20
150
225
100
200
85
120
Power Connector
Refrigerant Pipe
f
Gas Side 9.53(09unit.)
850
400
20
140
235
18
Hanging Bolt
4-M10 Field Accessory
Below
Ceiling
20
f
Gas Side 6.35)
f
12.7(12unit.)
Refrigerant Pipe
PANEL INSTALLATIONPANEL INSTALLATION
Make sure the following before installing the panel:
Downside of Indoor Unit and Ceiling must be in the same plane.
Indoor Unit must be parallel with the Ceiling Hole.
Check if there is water in the drain pipe.
Check if Refrigerant Pipe and the Drain Pipe has been connected and thermal protected.
Installation Procedure
1. Remove screws on panel
Positioning Board
Screw
Chart 13 Relative Position between the down side of Indoor Unit and Panel.
Panel Screws (M4 16) include the four screws used to install Model Paper of the Indoor Unit
and the one screw used to fix central of Indoor Unit temporarily.
Do not use Model Paper when installing the panel.
Remove Panel Screws and Model Paper.. (Chart 13)
Screw the bonnet of stop valve thoroughly.
9.
Chart 33
Manifold value
Multi-meter
-76cmHg
Lo-lever
Charge hose
Pressure meter
Hi-lever
Charge hose
Vacuum pump
Lo-lever
EXPEL AIR WITH A VACUUM PUMP
Screw the joint nuts A, B, C, D, and connect the charge hose of the manifold value with the charge
port of low-pressure valve.
Connect charge hose with vacuum pump.
Open the Lo-handle of manifold value (low pressure) thoroughly.
Turn on the vacuum pump. At the beginning of pumping, loosen the nut on the joint pipe of low
pressure valve to check whether the air has come in.
When the pumping is finished, close the Lo-handle completely and turn off the vacuum pump.
(Please refer to owner's manual for operation methods of manifold value)
1.
2.
3.
4.
5.
6.
7.
8.
When you have pumped for over 15 minutes, please confirm that the indicator or multi-meter is on
5
-1.0X10 Pa(-76cmHg).
Turn the valve stem of rotary valve deasil. About 6~7 seconds later, screw it.
Remove charge hose from the charge port of low-pressure side.
Open the valve stem of stop valve A and B thoroughly.
EXPEL AIR WITH REFRIGERANT TANK
Fasten the joint nuts C, D of indoor unit and A of outdoor unit.
Connect refrigerant charge hose with the charge port of low-pressure valve.
Loosen the joint nut B of outdoor unit a little.
Loosen the stop valve of the refrigerant tank and charge refrigerant for 10~15 seconds, then fasten
the stop valve.
Some refrigerant liquid flows from the joint nut. When the sound caused by flow decreases markedly,
fasten joint nut B.
Remove the charge hose from the charge port of low-pressure valve.
Discharge the remnant refrigerant from pipe with a screwdriver or similar tool pushing valve core (set
pin). When the sound of flow dies out, fasten the bonnet of stop valve.
Open the valve stems of high-pressure side and low-pressure side of outdoor unit.
Be sure the bonnet has been fastened.
1.
2.
3.
4.
5.
6.
7.
8.
5
12
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Midea MCB12HRN2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Midea MCB12HRN2 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Midea MCB12HRN2

Midea MCB12HRN2 Installatiehandleiding - Nederlands - 5 pagina's

Midea MCB12HRN2 Gebruiksaanwijzing - Nederlands - 9 pagina's

Midea MCB12HRN2 Gebruiksaanwijzing - English - 22 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info