785624
14
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
14 EN / SCM20 & SCM40 PWM User’s Manual
4 TROUBLE SHOOTING
If you cannot solve a problem with the aid of this chapter, contact your local Mastervolt Service Centre. See
www.mastervolt.com/technical-support. Make sure you have the following information present if you have to contact your local
Mastervolt Service Center to solve a problem: Article and serial number; see section 1.4
Malfunction Possible cause What to do?
No display function Battery voltage is abnormal Check battery voltage. Battery voltage must be
10~15V for 12V systems or 20~30V for 24V
systems.
Reversed polarity of the Battery Check wiring to battery
No voltage at Load
output
Fault condition See below error codes E1 ~E5
Wrong setting of the Load mode Check settings of the Load mode (section 2.6)
Short circuit at Load output Switch off all loads, remove short circuit. Load
output will automatically resume after 1 minute.
Overload at Load output Reduce the connected load. Load output will
automatically resume after 1 minute.
Battery voltage is too low; see section 2.6
for configuration of the Low voltage
disconnect function.
Reduce load connected to the batteries and
charge batteries. Load output will automatically
resume after 1 minute.
Overcharge, battery voltage is too high
(>15.5/31.0V)
Check batteries. Check other charging systems.
Use the battery temperature sensor.
Over temperature Check cooling of the Solar Chargemaster
No battery charging
during daytime
Batteries are full Nothing.
No power from the PV-modules.. Check wiring to PV-modules. Check for loose
connections, short circuit or incorrect polarity
Damaged battery temperature sensor Check battery temperature sensor (if applied)
Output voltage too low,
charger supplies
maximum current
Load that is connected to the batteries is
larger than charger can supply.
Reduce load taken from the batteries.
Batteries not 100% charged Measure battery voltage. After some time this will
be higher.
Wrong battery type setting Check settings (see section 2.6).
Battery is discharged too
fast
Battery capacity reduced due to sulphation
or due to plate corrosion
Charge and recharge a few times, this might help.
Check battery and replace if necessary.
Too low charger capacity or battery
capacity or too high load
Check balance between charger capacity, battery
capacity and load
Batteries are too warm,
gassing
Defective battery (short circuit in cell) Check battery and replace if necessary.
Battery temperature too high Use the battery temperature sensor.
Charge current too high for battery Check specifications of battery for maximum
allowed charge current
Wrong battery type setting Check settings (see section 2.6).
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Mastervolt Solar ChargeMaster SCM40 PWM bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Mastervolt Solar ChargeMaster SCM40 PWM in de taal/talen: Engels als bijlage per email.

De handleiding is 0.73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info