788781
4
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
4
ENGLISH
Bolt-down instructions
(For select models only)
WARNING: Product is not water resistant once it is bolted
down. The ETL verified water resistance claim applies to product
prior to the application of a bolt-down kit.
Bolt-down kit contents (in select models only):
• 2 lag screws
• 2 washers
• 2 masonry anchors
Tools needed to bolt safe to the floor:
• Drill
• Wrench
• 7⁄16” (11 mm) drill bit – for drilling into the safe
• 932” (7.2 mm) drill bit – for drilling into a wood floor
• 38” (9.5 mm) drill bit – for drilling into a masonry floor
WARNING: • DO NOT drill from any location inside the safe.
• DO NOT bolt through the walls.
1 Tip the safe onto its right side (door hinges horizontal with the floor).
2
F
Unlock the safe and open the door.
Look to the bottom of the safe for
two indentations on the feet in
opposite corners. Using the 7⁄16”
(11 mm) bit; drill a hole through
each indentation perpendicular to
the bottom of the safe. DO NOT drill
from any location inside the safe.
3 Tip the safe upright, place the safe in the desired location and
open the door.
4
F
Use a screw or pencil to mark the floor
through both holes.
5 Move the safe aside to clear both marked spots for drilling.
6 Drill into the floor:
F
A For wood: Using the 9⁄32” drill bit, drill
a hole 2-1⁄2” (64 mm) deep in each
marked spot.
B For masonry: Using the 38” drill bit,
drill a hole 2-1⁄2” (64 mm) deep in each
marked spot. Install a masonry anchor
in each hole.
7 Replace the safe in the desired position, with the holes in the safe
aligned with those in the floor.
8 Securing the safe:
F
A For wood: Pass each lag screw through a
washer, then through the safe and into a
hole. Tighten with the wrench.
F
B For masonry: Pass each lag screw
through a washer, then through the safe
and into a masonry anchor. Tighten with
the wrench. Place masonry anchors into
the holes in the floor.
NOTE: The safe should not be bolted to a wall, this will compromise
the fire rating. Drill holes through the feet only. DO NOT drill
through the back or sides.
Bolting/unbolting the unit is at the consumer’s expense and
discretion.
Master Lock is not responsible for any costs incurred if the
unit is to be replaced.
Troubleshooting
THE PROBLEM: WHY IT IS HAPPENING: THE SOLUTION:
The door will not lock. 1. Shipping screw is in place.
2. Confirm that there is no obstruction in the door.
3. Bolted down incorrectly.
1. Remove the screw on the back inside of the door.
2. Remove all items and accessories from inside the safe.
If this resolves the issue, re-set the accessories and
organize items to properly fit.
The handle is not
in the horizontal
position when the safe is
locked.
The clutch mechanism has
been engaged.
Rotate the handle up or down until it clicks into the
horizontal position.
Cannot open door after
inputting the combination or
electronic code.
1. Safe doors equipped with a water-resistant
gasket may initially be tight.
2. Key lock is in the locked
position. (select models only)
1. Hold the handle up while inputting the code or dialing
the combination and then pull down on the handle.
2. If your safe is equipped with a key lock ensure that the
key is in the unlocked position. (select models only)
The dial does
not turn.
1. Shipping screw is still in place.
2. Locking bolts are not fully extended.
1. Remove the screw from the back of the door.
2. Ensure the handle is in the horizontal position.
Red indicator light blinks three
times and there are
three beeps.
An incorrect code has been entered. Verify code and re-enter. If the programmable code you
are using doesn’t work then use the factory code. If
successful re-program your programmable code.
Red indicator light blinks five
times and there are five beeps.
Keypad communication error. Visit masterlock.eu/safes
Red indicator light blinks once
and there is one beep.
Program button is pressed out of sequence.
-or-
5 seconds has lapsed between button entries.
Start over.
Red indicator light
is blinking.
An incorrect code has been entered three times
and system has entered delay mode.
Wait two minutes and start over.
Yellow indicator light is on. Battery power is low. -or- Battery may be the
wrong type.
Replace with new alkaline batteries.
Registration
masterlock.eu/safes
By registering your Master Lock product you can easily retrieve
forgotten codes, combinations or order new keys should they be lost.
Registering also ensures the best customer service should you have a
question or concern regarding your Master Lock product. By registering
your Master Lock product you can also be sure that in the unfortunate
circumstance of a fire you will be guaranteed your replacement safe
(provided official paperwork).
Lifetime After-Fire
Replacement Guarantee
If your Master Lock product is in a fire it will be sealed shut making
it necessary for it to be pried open. To help your family begin again,
Master Lock will ship a replacement free of charge. To be eligible for
the After-Fire Replacement Guarantee you (the original owner) must
register your product by visiting masterlock.eu/safes.
Got a question?
If you ever have any questions regarding your Master Lock product,
please visit our website masterlock.eu/safes.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Master Lock LTW123GTC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Master Lock LTW123GTC in de taal/talen: Nederlands, Engels als bijlage per email.

De handleiding is 3.31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info