Handleiding Master Lock LTW123GTC (pagina 3 van 8) (Nederlands, Engels)

788781

Verklein

Vergroot

Pagina terug

1/8

Pagina verder

ENGLISH

2 A Slide out the battery drawer

on the side of the keypad.

B Insert 4 AAA alkaline

batteries (not included)

Note: Do not use rechargeable

batteries or any other type of

non-alkaline battery. Do not mix

old and new batteries. Do not mix

alkaline and standard batteries.

C Slide battery drawer back

into keypad.

M100TEST

SN100TEST01*

12345

Find your 5 digit factory code on

the back of this owner’s manual.

WARNING: Test your code several times before putting

valuables inside.

Unlocking your safe

1 FOR DUAL KEY/COMBINATION

LOCKS ONLY, insert key into the

lock, turn to the ’unlocked’

position, then remove the key

This is a secondary locking

feature not an override key.

2 A Enter the 5 digit factory code

found on the back of the

owner’s manual.

Note: You may have to lift

the handle while entering

the combination.

B A green light will indicate the

code is correct. You will have

4 seconds to turn the handle

to unlock your safe.

3 Rotate the handle downward to

open the door.

This may take a limited

amount of force if you have a

water-resistant safe.

NOTE: • Make sure the handle is rotated all the way up in the

horizontal position before unlocking the safe.

• If you exert too much force on the handle, the handle will

move without moving the bolts. If this happens, you will

hear a ’click.’ DO NOT be alarmed. This feature is designed

to protect the bolts from being over powered by force. If this

occurs, simply exert force in the opposite direction (lifting up)

until the handles ’clicks’ back into place and repeat steps 1-3

to open your safe.

• Delay mode will occur if three consecutive invalid entries have

been tried. Red LED will blink on and off to let you know the

safe is in delay mode. This will cause the system to shutdown

for two minutes. DO NOT remove the batteries to restart the

system it will only increase the length of time for the system

shutdown.

Locking your safe

1 Close the door and pull the

handle upward until the handle is

horizontal.

For water-resistant units,

additional pressure to the front,

left side of the door may need

to be applied prior to rotating

the handle.

2 FOR DUAL KEY/ELECTRONIC

LOCKS ONLY, insert key into the

lock, turn to the ’locked’ position,

then remove the key.

NOTE: If your safe does not

appear to be working properly,

please check to make sure you

are using NEW alkaline batteries

before contacting Master Lock

Customer Service.

Programming information

Three code options:

Factory code:

The safe will ALWAYS unlock using

this 5 digit code (found on the back of

the owner’s manual). This code cannot

be deleted.

User code:

A 5 digit programmable code of your

choosing that can be changed or

deleted or changed.

Secondary code:

A second 5 digit programmable code of

your choosing that can be changed or

deleted. Can only be programmed after

a user code has been activated.

NOTE: • The “C” key is a clear key. This can be used at anytime to

clear the system and return to standby mode – unless you are

in delay mode (3 consecutive invalid entries).

• The 5 digit factory code cannot be deleted. However, you may

add and delete additional codes.

This safe can store up to three codes at one time. One factory

code and two additional programmable codes.

Programming the user code

To ADD a user code:

1 Press the “P” key.

2 Enter the 5 digit factory code found on the back of your owner’s

manual.

3 The light will ﬂash green and then you will have ﬁve seconds to

enter your own personal 5 digit user code.

To DELETE a user code:

1 Press the “P” key.

2 Enter the 5 digit factory code.

3 Enter 0,0,0,0,0.

NOTE: • The electronic lock will NOT indicate that it has deleted the

user code – please test the code to make sure it has been

deleted.

• Test with door open when programming.

Programming the secondary code

To ADD a secondary code:

1 Press the “P” key two times.

2 Enter the 5 digit user code previously programmed.

3 The light will ﬂash green and then you will have ﬁve seconds to

enter your own personal 5 digit secondary code.

To DELETE a secondary code:

1 Press the “P” key two times.

2 Enter the 5 digit user code.

3 Enter 0,0,0,0,0.

NOTE: • The electronic lock will NOT indicate that it has deleted the

secondary code – please test the code to make sure it has

been deleted.

How to operate the light

The safe you have purchased may include a light. This is a long-lasting

LED light. Not all safes include a light.

The batteries that operate the keypad

are the same batteries that operate the

light. If the light in your unit does not

turn on, please change your batteries.

The light will turn on every time you

enter your code and will remain on

for 30 seconds. The light duration has

three options – off, 30 seconds, and 60 seconds.

To turn the light off:

1 Press the “0” button.

2 Press the “P” button.

3 Press the “3” button.

To turn the light on for 30 seconds:

1 Press the “0” button.

2 Press the “P” button.

3 Press the “4” button.

To turn the light on for 60 seconds:

1 Press the “0” button.

2 Press the “P” button.

3 Press the “5” button.

NOTE: • If the light duration is 60 seconds, the battery life will be

reduced at a faster rate.

Operating sound features

For Programmable Electronic Lock Only

The tones of the key pad may be turned on and off depending on user

preference.

Turn sound off:

1 Press “O”.

2 Press “P” key.

3 Press “2”.

Turn sound on:

1 Press “O”.

2 Press “P” key.

3 Press “1”.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Master Lock LTW123GTC Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info