494328
10
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
55
Do not open the product: the device contains live parts. The
product should only be repaired or serviced by a qualified
repairman.
In case of improper usage or if you have opened, altered and
repaired the product yourself, all guarantees expire. Marmitek
does not accept responsibility in the case of improper usage
of the product or when the product is used for purposes other
than specified. Marmitek does not accept responsibility for
additional damage other than covered by the legal product
responsibility.
56
The RF communication uses the 433.92 MHz
communication band. This band is a non-exclusively
available communication band. Therefore, interference
and limitations in range cannot be completely eliminated.
The range of the RF signals depends on a number of (external)
factors. Some of these factors are: transmitter power,
installation method and site, air humidity and construction of the
home. The materials used in homes hinder the transmission of
RF signals to some extent. Consequently, the maximum
communication distance in homes is less than the distance that
can be achieved in the open. The following list gives the
damping effect of several materials.
Absorption of RF signals
Wood, plaster, plasterboard approx. 10 %
Brick and stone, chipboard approx. 30 %
Reinforced concrete approx. 70 %
Metal (gauze), aluminium (foil) approx. 90 %
RF-signals
57
Technical data
Product characteristics
Mains voltage 230 Vac, 50 Hz
Max. power consumption < 2 W
Ambient temperature 0 to 40 °C
Frequency 433,92 MHz; X-10 RF (NEC)
compatible protocol
Max communication distance 100 m (open field)
Protection class Class II, Double insulated
Type of protection
IP 40 with wall or ceiling installation
IP 20 with installation on the wall
Standards IEC 60950
Housing
Dimension (H x W x D) 120 x 80 x 30 mm
Color RAL9001
Power cable
Dimension Length 1.5 m
Color White
58
Troubleshooting
Problem: The LED on the RFIX35 does not flash when I press the
remote control.
Cause: The remote control batteries are (almost) flat.
Solution: Replace the batteries.
Cause: The remote control (ABX1) is in the IR mode and not in the
RF mode.
Solution: Set the remote control to a RF transmitter.
Cause: The RFIX35 is not set to the same letter code as the remote
control.
Solution: Program in the same letter code on the remote control and the
RFIX35 or program the RFIX to letter code P.
Cause: The remote control is not programmed to the RF-secured mode
but the RFIX35 is.
Solution: Set the remote control to the RF-secured mode.
Cause: The remote control is programmed to the RF-secured mode but
the RFIX35 is not.
Solution: Set the remote control to the standard receive mode.
Cause: The RFIX35 is in the RF-secured mode and the remote control is
not linked.
Solution: Link the remote control in the RF-secured mode.
Cause: RF signals are not received.
Solution: Reduce the distance between the remote control and the RFIX35.
59
Problem: The transmission range is insufficient.
Cause: The receiver is too close to metal parts.
Solution: Ensure that the RFIX35 is placed away of metal parts. Do not
place on a metal plate.
Cause: Radio frequency signal interferes with the receiver.
Solution: Place the RFIX35 out of range of other electronic equipment.
Cause: The batteries are almost flat.
Solution: Replace the batteries.
Problem: There are spontaneously switching modules.
Cause: Commands from neighbours are received by the RFIX35.
Solution: Do not set the receiver to the same letter code as the neighbours.
Do not set the RFIX35 to letter code P but to a single letter code.
Set the RFIX35 to the RF-secured mode.
Cause: The RFIX35 is set to letter code P and is not programmed to the
RF-secured mode.
Solution: Set the RFIX35 to the RF-secured mode.
60
Troubleshooting (cont'd.)
Problem: After the remote control batteries are replaced, I cannot
operate anything.
Cause: The remote control batteries are incorrectly positioned or make
insufficient contact.
Solution: Check if the batteries are correctly positioned.
Cause: The letter code of the remote control has been reset to
letter code A.
Solution: Program the correct letter code into the remote control.
Cause: The remote control generates a new RF-security code that is not
recognised.
Solution: Delete all security codes in the RFIX35 and link the remote control
again.
Problem: When programming in the security code, the LED lights up
for 2 seconds.
The RFIX35 does not accept any more security codes.
Cause: The RFIX35 memory is full. All 8 remote controls are linked in the
RF-security mode.
Solution: Clear the RFIX35 memory and link the remote control(s) again.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Marmitek RFIX35 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Marmitek RFIX35 in de taal/talen: Nederlands, Engels als bijlage per email.

De handleiding is 0,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info