494328
9
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
49
The RFIX35 is now in the
RF-secured receiving mode. To link
a remote control please send an
address and a command with the
remote control in the RF-secured
mode (see page 51 and 52) that you
want to link to the RFIX35.
When the RFIX35 accepts the
remote control the RFIX35 will
return to the operation mode (LED OFF).
If you want to link more remote controls please repeat this
procedure for all other remote controls you want to link up to a
maximum of 8. When the memory of the RFIX35 is full it will not
50
Programming the RFIX35 (cont'd.)
accept any remote control. The LED of the RFIX35 will be lit for
2 sec. and will return to the normal operation mode without
storing the remote control. If you accidentally link a remote
control that was already linked it will be accepted without
"claiming" any extra memory space.
Note: If the same remote control is linked with a
new random generated security code, extra memory
space will be claimed.
The RFIX35 will automatically return to the operation mode when
it does not receive any commands within 60 seconds.
Delete all linked remote controls from memory
If you have already linked 8 remote controls and want to link a new
remote control to the RFIX35, you will first have to clear the
memory of the RFIX35. This is possible by first setting the RFIX35
in the RF-secured programming mode (keep programming switch
pressed and release the switch after 6 seconds. The LED will give
quick short blinks). In the RF-secured mode press the programming
switch and keep it pressed. Release the programming switch after
9 seconds. All previously linked remote controls are now deleted,
the memory is cleared. You can now start the procedure as
previously described to link up to 8 remote controls again.
3
!
51
Programming of the remote control
Programming the RF-secured mode in the remote control
To be able to use the RF-secured mode you first have to
program the remote control to the RF-secured mode.
To program the RF-secured mode in the ABX1 or ABX3 please
follow the steps below.
Setting ABX1 to RF-secured mode
1.
Program in the code 822 via the Marmitek X-10 key
Press SETUP until the LED stays lit
Press the Marmitek X-10 key
Enter 8-2-2, the LED goes out after the last 2
2. Press the Marmitek X-10 key
3. Press SETUP until the LED stays lit
4. Release the SETUP key.
5. Press the A.B. key to generate a random
security code
6. Press the ENT (Enter) key
Return to the standard mode (= non-RF-secured mode)
To return the ABX1 to the standard mode, program in the code
820 via the Marmitek X-10 key.
Press SETUP until the LED stays lit
Press the Marmitek X-10 key
Enter 8-2-0, the LED goes out after the 0
52
Programming the remote control (cont'd.)
Setting ABX3 to RF-secured mode
1. Remove the batteries.
2. Press the keys to release the last bit of energy
from the remote control.
3. Set the switch to position 2.
4. Now place the batteries in the remote control.
Return to the standard mode (= non-RF-secured mode)
To return the ABX3 to the normal mode, follow the
instructions below:
1. Remove the batteries.
2. Press the keys to release the last bit of energy from the
remote control.
3. Set the switch to position 1.
4. Now place the batteries in the remote control.
53
The RFIX35 is designed to be:
- installed on a standard 50 mm junction box or
- installed below a (ceiling) distribution box, or
- mounted on a wall (using supplied power cable).
When installing in a meter box, you must ensure that the plug
of the RFIX35 is inserted in a socket that is electrically "after"
the filter.
Note: Automatic switching does not just increase
the level of comfort, a number of hazards are also
involved. People may be surprised, or clothing pla-
ced over an electrical heat source may ignite.
Always be aware of these hazards and take the
necessary precautions.
The product must only be opened for installation purposes.
We advise you to have the product installed by a trained and
certified Marmitek X-10 dealer.
!
Installation methods
54
Installation methods (cont'd.)
If the mains lead supplied is used, the wire ends must be
installed up to the insulation in the connector. There must not
be any bare copper visible.
Ensure that the built-in antenna is at a sufficient distance from
metal parts and cabling.
Never install the RFIX35 against a metal rear wall.
Install the RFIX35 at a sufficient distance from other
RF transmitters, such as WIFI routers and DECT telephones
etc. This equipment can interfere with the reception of the
RFIX35. Install the RFIX35 at least 1.5 metres from such
equipment, as centrally as possible in the home (in electrical
terms).
To prevent short circuits, this product should only be used
inside and only in dry spaces. Do not expose the components
to rain or moisture. Do not use the product close to a bath,
swimming pool etc.
Do not expose the components of your systems to extremely
high temperatures or bright light sources.
Only connect the product to the mains after checking
whether the mains voltage is the same as the values on the
identification tags. Never connect a power cord when it is
damaged. In that case, please contact your supplier.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Marmitek RFIX35 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Marmitek RFIX35 in de taal/talen: Nederlands, Engels als bijlage per email.

De handleiding is 0,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info