494268
7
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
4 flashes for 8 minutes.
5 flashes for 16 minutes.
6 flashes for 32 minutes.
7 flashes for 62 minutes.
8 flashes for 128 minutes.
9 flashes for 255 minutes.
Release the <unit/off> button.
Now press the <unit/off> button the number of times that corresponds to the mode that you want to
set. On the last press hold down the button (e.g. for a 4-minute delay press the <unit/off> button 3
times and hold the button down on the third press)
After 3 seconds the LED will display the new setting and the LED will switch off.
The MS13 saves the settings in non-volatile memory so that the settings are kept when the batteries are
changed.
NOTE: The MS13 cannot activate alarm functions on Marmitek Alarm systems. Use the MS90 for this.
FREQUENTLY ASKED QUESTIONS
What is the reason for modules to switch on/off spontaneously?
It is possible that a Marmitek X-10 System is installed at one of your neighbours using the same House
Code. To solve this problem try to change the House Code of your system, or have FD10 Phase
Coupler/Filter installed at your incoming mains.
My modules will not respond to my controller.
Make sure that the House Code on all Modules and Controllers are set to the same House Code (A .. P).
My modules will not react to my remote / sensor.
When you use a remote or sensor, you should have at least one TM13 Transceiver or Marmitek Security
Console installed in your house. These components will translate the radio signals to the Marmitek X-10
signal on the power line. Only one Transceiver should be installed for all remotes and sensors set to the
same House Code.
Am I able to increase the range of my remotes by using more Transceivers?
Yes, you can use more than one TM13 Transceiver in your home when the range of your remotes is not
sufficient. The TM13 is using so called collision detection to prevent signals to be disturbed when more
than one TM13 is transmitting. TM13’s will wait for a quite power line before transmitting their data. To
prevent your Marmitek X-10 System to become slow or to prevent dimming from becoming less smooth,
make sure that the TM13 units are placed as far away from each other as possible.
Do you still have questions?
Please check out www.marmitek.com for more information.
TECHNICAL SPECIFICATIONS
Power supply: 2x AAA battery
RF frequency: 433.92 MHz
RF Range: Up to 30m free field, up to 20m through walls and ceilings
RF Power: 1mW
PIR range: 45º - 5 metres, straight ahead - 12 metres
Ambient temperature: - 10°C to + 30° C (operation) - 20°C to + 70° C (storage)
Dimensions: 67x67x27mm
7MS13
TM
ENGLISH
manual MS13 05-12-2006 09:54 Pagina 7
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Marmitek MS13 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Marmitek MS13 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 0,31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info