494268
5
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
The MS13 is fully wireless, the signal is transmitted straight through walls and ceilings and it is
suitable for outdoor use.
OPERATION
The MS13 motion detector sends radio signals to an X10 transceiver (Marmitek X10 TM13 or Marmitek X10
Alarm station). The transceiver or station then transmits these signals wirelessly via the electric cabling that is
already in your house to switch lights (or appliances) that are connected to X10 receivers on and off. The
Marmitek X10 TM13 and a Marmitek X10 CM11 computer interface can also be used to activate previously
programmed macros. The MS13 can also be programmed to detect motion both at night and during the day,
or only at night. The Marmitek X10 MS13 can also be used to detect the transition from light to dark and
vice versa.
INSTALLATION
Slide the antenna sleeve over the sensor’s wire antenna. Press the sleeve into the clamp on the top of the
sensor. Insert 2 AAA batteries into the MS13’s battery compartment. The cap on the front of the sensor
must be removed using tweezers or small pliers in order to open the battery compartment. Now the screw
that is locking the lid can be unscrewed. Replace the cap if the sensor is to be used outdoors.
After inserting the batteries it will take 30 seconds for the MS13 to become active.
After a signal has been transmitted the MS13 will be inactive for 10 seconds.
The default setting for the house-code that is transmitted is A (factory setting).
The default setting for the unit-code that is transmitted for motion detection is 1 (factory setting).
The unit-code that is transmitted for light / dark detection is always the unit-code that has been set + 1
(example: If you have the motion detection code set to A3 the code for light/dark is automatically A4).
The default setting for this function is off (factory setting).
When motion is detected an <on> command is transmitted.
When the <house/on> button is pressed once an <on> command is transmitted.
When the <unit/off> button is pressed once an <off> command is transmitted.
On transition from light to dark an <on> command is transmitted for the unit-code that has been
set +1.
On transition from dark to light an <off> command is transmitted for the unit-code that has been
set +1.
When motion is detected an <on> command is transmitted for the unit code that has been set.
After the last motion detection plus the set delay (factory setting 1 minute) an <off> command is
transmitted for the unit code that has been set.
PROGRAMMING THE HOUSE-CODE
Unlike most Marmitek X-10 Modules the MS13 does not have code wheels.
Press the <house/on> button and hold it down.
The red LED will start to flash.
3 seconds later the LED will display the current house-code setting (the factory setting is A).
1 flash for A.
2 flashes for B.
• …
16 flashes for P.
Release the <house/on> button.
5MS13
TM
ENGLISH
manual MS13 05-12-2006 09:54 Pagina 5
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Marmitek MS13 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Marmitek MS13 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 0,31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info