494327
5
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
Marmitek X-10
Infrared interface type IRIX35
26
Technical characteristics
Transposes 38 kHz InfraRed (IR) signals from the remote
control device into Marmitek X-10 commands on the power
line.
Axial sensitivity: 25 mtr. range (edge 45°, 7 m. range).
Possibility for standard and "toggle" IR receipt.
Possibility to control one user definable letter code
(16 addresses).
Designed as an wall- or ceiling mountable unit or for
stand-alone use.
The infrared protocol is compatible with the existing
X10 IR-protocol. This means that all standard X10 compatible
IR remote transmitters (controls) can be used.
Application options
The IRIX35 can be used to receive infra red-commands (IR) from
Marmitek X-10 remote controls and send them over the power
line to switch or dim Marmitek X-10 actuators (see figure 1).
Marmitek X-10 Infrared interface type IRIX35
27
Figure 1.
Marmitek Home Control Box
If the IRIX35 is used in combination with the Marmitek Home
Control Box. The IRIX35 can be used to activate the previously
programmed macros in the Marmitek Home Control Box, using a
remote control device.
Marmitek X-10 modules
IRIX35
Infrared
signals
Remote control
Marmitek
Home Control
Box
Lighting
circuit
signal
28
In principle, the IRIX35 can be used in two ways:
1. Fitted to a distribution box.
2. Connected to a wall socket.
Note: Switch off the power before starting the
assembly!
Fitting to a distribution box
To fit the IRIX35 to a distribution box, follow the steps below.
Remove the cover of the IRIX35 by loosening the screw at
the top.
Feed live and neutral through the rear plate by making an
opening through the sticker covering the mounting plate.
Firmly screw the mounting plate with screws to the
distribution box.
Connect live and neutral to the connector of the
mounting plate.
Firmly tighten the cover of the IRIX35 to the mounting
plate again.
!
Assembly
29
A
Fitting to a distribution box.
30
Connecting the power cord for use in a wall socket
If you wish to connect the IRIX35 to a wall socket, you must
connect the power cord provided.
To connect the power cord to the IRIX35, follow the steps
below.
Remove the cover of the IRIX35 by loosening the screw
at the top.
Use a Stanley knife to carefully cut open the recess on the
narrow side of the mounting plate so that the power cord
can be fed through.
Fit live and neutral to the connector and feed the cable
through the cable channel in the mounting plate.
Firmly tighten the cover of the IRIX35 to the mounting
plate again.
Assembly
(cont'd.)
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Marmitek IRIX35 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Marmitek IRIX35 in de taal/talen: Nederlands, Engels als bijlage per email.

De handleiding is 0,22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info