600703
10
Verklein
Vergroot
Pagina terug
1/30
Pagina verder
10
Adjusting the cutting angle
WARNING:
Do not operate the tool with the loose and unstable
cutter unit. Otherwise the cutter unit may change
direction suddenly and cause injury.
CAUTION:
The cutter unit is fastened only with certain angles
alongside the groove on the unit. Make sure the cutter
unit sits properly. If the angle is not appropriate, the
clutch is cut and the tool does not operate.
Do not adjust the cutter unit while the pole hedge
trimmer is in an upright position.
Switch off the tool and remove the battery cartridge,
and lay the pole hedge trimmer flat on the ground to
adjust the cutting angle.
Always secure the blades with the blade cover
provided before adjusting cutting angle. (Fig. 8)
You can adjust the cutting angle upwards to 45° and
downwards to 90°.
1. Remove the battery and lay the machine on the
ground.
2. To adjust the angle of the cutter unit, hold the handle
on the cutter unit with one hand, and hold the angle
lock as illustrated with the other hand.
3. Pull the angle lock gently, and change the angle of the
cutter unit. After adjusting the angle, return the angle
lock gently. (Fig. 9)
In case the cutter unit is loose, the bolt (the axis of angle
adjustment) needs to be tightened.
4. Set the socket wrench and the hex wrench on the bolt.
5. Adjust the tightness of the cutter unit by turning hex
wrench, and then fasten the bolt by turning the socket
wrench.
NOTE:
Do not fasten the cutter unit too tight. The angle of the
cutter unit can not be changed if it is too tight.
ASSEMBLY
WARNING:
Always be sure that the tool is switched off and
battery cartridge is removed before carrying out
any work on the tool. Failure to switch off and remove
the battery cartridge may result in serious personal
injury from accidental start-up.
Never start the tool unless it is completely
assembled. Operation of the tool in a partially
assembled state may result in serious personal injury
from accidental start-up.
Installing the battery guard (Fig. 10)
Install the battery guard and tighten it with four screws.
Installing the loop handle (Fig. 11)
Securely fit the loop handle onto the shaft pipe with two
screws and clamps.
Make sure that the loop handle assembly is located
between the front grip and the arrow mark.
Attaching shoulder harness (Fig. 12)
Put the shoulder harness on your left shoulder by putting
your head and right arm through it. Keep the tool on your
right side.
After putting the shoulder harness, attach it to the tool by
connecting the buckles provided on both the tool hook
and the harness. Be sure that the buckles click and lock
completely in place.
Adjust the strap to the suitable length for your operation.
(Fig. 13)
The buckle is provided with a means of quick release
which can be accomplished by simply squeezing the
sides and the buckle.
WARNING:
Be extremely careful to maintain control of the tool
at all times. Do not allow the tool to be deflected
toward you or anyone in the work vicinity. Failure to
keep control of the tool could result in serious injury to
the bystander and the operator.
OPERATION (Fig. 14)
Do not attempt to cut branches thicker than 20 mm
diameter with this trimmer. These should first be cut with
shears down to the hedge trimming level.
CAUTION:
Do not cut off dead trees or similar hard objects. Failure
to do so may damage the tool.
Horizontal cut (Fig. 15)
When trimming hedges horizontally, follow the steps
below.
1. Pull the switch trigger fully.
2. Apply the blades to the hedge with an angle of 15° to
30°.
3. Trim the hedge with a swinging movement.
Vertical cut (Fig. 16)
When trimming hedges vertically, follow the steps below.
1. Pull the switch trigger fully.
2. Apply the blades to the hedge parallel to each other.
3. Trim the hedge from the bottom upwards with a
swinging movement.
MAINTENANCE
WARNING:
Always be sure that the tool is switched off and
battery cartridge is removed before attempting to
perform inspection or maintenance on the tool.
Failure to switch off and remove the battery cartridge
may result in serious personal injury from accidental
start-up.
Before handling or working around blades, wear
protective gloves and put the blade cover onto blades.
During the assembly or adjustment, your fingers may
contact with blades and it may cause serious injury.
When inspecting or maintaining the equipment, always
put the hedge trimmer down. Assembling or adjusting
the equipment in an upright position may result in
serious injury.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita UN490D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita UN490D in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens als bijlage per email.

De handleiding is 0,75 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info