168723
14
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
A M P L I F I E R S
ENG
TROUBLE SHOOTING
The key to finding the problem in a misbehaving sound system is to isolate
parts of that system in a logical fashion to track down the fault. Description
of the Diagnostic system built into all MB Quart amplifiers:
The diagnostic system will shut down the amplifier, until reset by turning the
head unit off, and back on. This state of affairs will be indicated by the front
panel PROTECT LED lighting up under the following conditions:
1 - A short circuit on the loudspeaker leads.
2 - An internal amplifier fault that causes a DC offset on the loudspeaker
output.
Should the amplifier go into diagnostic mode, simply disconnect all RCA and
speaker leads, while keeping +12 volt, power ground and remote leads connected.
1 - Now turn the amplifier back on, and if the diagnostic LED lights, the
amplifier has an internal fault.
2 - If not, plug the RCA cables back, and reset the amplifier. If it goes into
diagnostic now, the fault lies in the input, either with bad cables or source
unit.
3 - If the amplifier seems fine with RCA cables plugged in, connect the speakers,
one at a time, and if one of the speakers or its wiring is faulty, it will
activate the diagnostic system.
Amplifier heatsink overheating
The amplifiers will shut down when the heatsink temperature reaches 80° C,
and turn back on once the unit has cooled down below that point.
Causes of overheating:
1 - Inadequate cooling - relocate or remount to provide better natural airflow
over the fins.
2 - Driving high power levels into low impedances - back off on the volume
control, and/or make sure you are not loading the amplifier with less than
the recommended loudspeaker impedance.
Low output power
1 - Check that level controls have been set up properly.
2 - Make sure that the battery voltage, as measured at the amplifier’s +12 volt
and ground terminals, is 11 volts or more.
3 - Check all +12 volt and ground connections.
Fuses blowing
1 - The use of loudspeaker impedances below the recommended minimums
will draw more current - check.
2 - A short on the main +12 volt cable from the battery to the vehicle chassis
will cause the main fuse to blow.
3 - If an amplifier fuse blows continually, with only +12 volt, ground and
remote leads connected, the amplifier may be faulty.
System does not turn on
1 - Check all fuses.
2 - Check all connections.
3 - Measure the +12 volt and remote turn on voltages at the amplifier terminals.
If these are non existent or low, take voltage measurements at fuse holders,
distribution blocks, the head unit’s +12 volt and remote leads to localize
the problem.
Noise problems
System noise can be divided into two categories, hiss, and electrical interference.
Hiss, or white noise
1 - High levels of white noise usually occurs when amplifier level controls are
turned up too high - readjust according to the procedures in sectionSetting
up systems after installation for best performance”
2 - Another major problem that can cause excessive hiss, is a noisy head unit
- unplug the amplifier input RCA cables, and if the hiss level reduces, the
source unit is at fault.
Electrical interference
The inside of an automobile is a very hostile electrical environment. The
multitude of electrical systems, such as the ignition system, alternator, fuel
pumps, air conditioners, to mention just a few, create radiated electrical fields,
as well as noise on the +12 volt supply and ground. Remember to isolate the
problem - first unplug amplifier input RCA cables, if the noise is still present,
check the speaker leads, if not, plug the RCAs back, and investigate the source
driving the amplifier, one component at a time.
A ticking or whine that changes with engine RPM
1 - This problem could be caused by radiation pickup of RCA cables too near
to a fuel pump or a distributor, for instance, - relocate cables.
2 - Check that the head unit ground is connected straight to the vehicle chassis,
and does not use factory wiring for ground.
3 - Try to supply the head unit with a clean +12 volt supply directly from the
battery +, instead of using a supply from the in dash wiring/fusebox.
A constant whine
This type of noise can be more difficult to pinpoint, but is usually caused by
some kind of instability, causing oscillations in the system.
1 - Check all connections, especially for good grounds.
2 - Make sure that no speaker leads are shorting to exposed metal on the
vehicle chassis.
3 - RCA cables are notorious for their problematic nature, so check that these
are good, in particular the shield connections.
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw MB Quart dsc4125 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van MB Quart dsc4125 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 6,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info