168723
13
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
ENG
M O N O - A M P L I F I E R S
DSC1500.1D
FEATURES:
• PROTECTION and POWER LED indicators
• The REMOTE jack enables a dash mount control for the BASS BOOST
• BALANCED INPUT: balanced MINI-DIN signal input
NOTE: DO not use this input with the RCA input at the same time.
• LOW PASS: Variable from 35Hz to 250Hz
• SUBSONIC FILTER: Variable from 15Hz to 35Hz
• PHASE: Variable from 0 to 180
• BASS BOOST: 45Hz bass boost from 0dB to 9dB
• INPUT LEVEL sensitivities are variable from 0.2volts to 6volts
• Each model is capable of 1ohm minimum
3. Bass Remote Module:
Plug in the optional Remote Bass Module to the REMOTE jack and control the
Bass Boost setting.
4. Mode-Switch:
The „MODE“ switch must be on „MASTER OUTPUT“ position.
IMPORTANT: Minimum final loudspeaker impedance must be not lower than 1ohm.
1. Interconnect cable checklist:
Connect mono line input via Y-adapter from mono source or single
Left or Right RCA from stereo source.
IMPORTANT: Do not connect the Left and Right stereo signals
together to achieve a mono signal as this will damage the output
stage of source and possibly the input stage of the amplifier.
- Use at least 1,5 sqmmspeaker wiring. These amplifiers feature dual speaker
terminals, simplifying the hookup of multiple speakers.
STANDARD OPERATION
PARALLEL MONO
SUBWOOFERS
2 OHMS EACH MINIMUM
MONO
LINE INPUT
BASS-REMOTE
SUBWOOFER
+12V BATTERY
REMOTE TURN-ON
CHASSIS GROUND
SUBWOOFER
WITH DUAL-
VOICE COIL
4. Bass Remote Module:
Plug in the optional Remote Bass Module to the REMOTE jack of the „MASTER“ amp
and control the Bass Boost setting of both amps together.
IMPORTANT: Minimum final loudspeaker impedance must be not lower than 2ohm.
Check the below featured connection figures.
1. Interconnect cable checklist MASTER:
Connect mono line input via Y-adapter from mono source or single
Left or Right RCA from stereo source into the „MASTER“ amp.
2. Interconnect cable checklist SLAVE:
Connect a mono line cable from „MASTER OUTPUT “ of the „MASTER“ amp
with the „SLAVE INPUT “ of the „SLAVE“ amp.
3. Mode Switch:
The „MODE“ switch of the „MASTER“ amp must be in position „MASTER OUTPUT“.
The switch of the „SLAVE“ amp in position „SLAVE INPUT“.
MASTER/SLAVE OPERATION
Amplifiers can run at a 2 ohm load
minimum when linked.
2 SUBWOOFERS
WITH SINGLE-
VOICE COIL
+12V BATTERY
REMOTE TURN-ON
CHASSIS GROUND
+12V BATTERY
REMOTE TURN-ON
CHASSIS GROUND
MONO
LINE INPUT
BASS-REMOTE
BRIDGING
JUMPER CABLE
MASTER TO SLAVE
RCA JUMPER
CABLE
INVERT POLARITY
ON VOICE COIL 2
INVERT POLARITY
ON SUBWOOFER 2
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw MB Quart dsc4125 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van MB Quart dsc4125 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 6,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info