626350
54
Verklein
Vergroot
Pagina terug
1/99
Pagina verder
HARDWARE
45
ROVING PROBE TEST
The Roving Probe Test will help uncover problems
with TestBook hardware. Run this test whenever you
suspect a problem with the Roving Probes.
Before running this test, make sure the Roving
Probes are plugged into the back of TestBook. Hold
both of the individual probes in your hands,
disconnected from any power source.
To run the test, move the scroll box at the RDS
Integrity Tests screen until Roving Probe is selected.
Then touch Continue. The Roving Probe Test
screen will appear and the test begins automatically.
How To Interpret the Results of the Roving Probe
Test
Two tests will be run to test the Roving Probe
hardware. A result will appear after each test is
finished. The tests are described as follows:
Touch Roving Probes Together This test makes sure that the Roving Probes can complete a closed
circuit. you must hold the probes together for at least ten full seconds.
If either of the probes has an open circuit, it will appear during this
test.
Touch the Roving Probes together as instructed. You should see the
"PASSED" message appear.
If there is no response. check the following:
Make sure the Roving Probes are securely plugged into the back
of TestBook.
Check the cables for cracks or cuts.
Check the fuse in the back of TestBook. Replace the fuse if
necessary with a 1 amp fuse of the same size. See "Fuse
Replacement" in the TestBook Installation Guide section.
Connect Roving Probes to a
Battery (1.5 to 12 Volts)
This test verifies that TestBook can measure voltage When you make
the connection to any battery rated between 1.5 and 12 Volts, a
readout of the voltage will appear in a box near the middle of the
screen. Be sure to connect the red probe to the battery " +" and the
black probe to the battery " -". When the voltage is measured steady
for ten seconds, the test will respond "PASSED". (To account for
strong or worn batteries, the test will PASS with any steady voltage of
between 1 and 18 Volts).
If your test battery does not have between 1.5 to 12 volts, or
TestBook cannot read the voltage, the message "FAILED" will
appear. Check the following:
Check that the Roving Probes are still securely plugged into
TestBook.
Check the fuse in the back of TestBook. Replace the fuse if
necessary with a 1 Amp fuse of the same size. See "Fuse
Replacement" in the TestBook Installation Guide section.
Check the battery using another tool to make sure that the voltage is
between 1.5 to 12 volts.
If service appears necessary, contact the Testbook
HelpDesk to verify the problem.
54

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Land Rover TestBook bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Land Rover TestBook in de taal/talen: Engels als bijlage per email.

De handleiding is 1,01 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info