680891
68
Verklein
Vergroot
Pagina terug
1/2025
Pagina verder
If the parameters -s and/or -f are not specified, the device uses default values set in path
/setup/config/TFTP-Client:
1
Config address
1
Config file name
1
Firmware address
1
Firmware file name
These default values can be used if the latest configurations and firmware versions are always stored under the same
name in the same location. In this case, the simple commands LoadConfig and LoadFirmware can be used
to load the relevant files.
3.8 How to reset the device?
If you have to configure the device regardless of possible existing settings, or if a connection to the device configuration
failed, you can put back the device into the factory default state with a Reset. To do so, push the Reset button until
the device LEDs will light up (approx. 5 seconds).
5
After applying the reset, the device will start fresh with factory defaults. All settings will be lost. Therefore, you
should save the current configuration if possible before the reset!
5
Please notice that also the WLAN encryption settings of the device will get lost in case of a reset and the standard
WEP key comes into effect again. The wireless configuration of a device with WLAN interface will only succeed
after a reset, if the standard WEP key is programmed into the WLAN adapter!
The reset button offers two basic functions—boot (restart) and reset (to the factory settings)—which are called by
pressing the button for different lengths of time.
Some devices simply cannot be installed under lock and key. There is consequently a risk that the configuration will be
deleted by someone pressing the reset button too long. With the suitable setting, the behavior of the reset button can
be controlled accordingly (only for devices with serial configuration interface):
WEBconfig: LCOS Menu Tree / Setup / Config
1
Reset button
This option controls the behavior of the reset button when it is pressed:
2
Ignore: The button is ignored.
5
Please observe the following notice: The settings 'Ignore' or 'Boot only' makes it impossible to reset
the configuration to the factory settings using the reset button. If the password is lost for a device with
this setting, there is no way to access the configuration! In this case the serial communications interface
can be used to upload a new firmware version to the device-this resets the device to its factory settings,
68
Reference Manual
3 Configuration
68

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Lancom LCOS 9.10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Lancom LCOS 9.10 in de taal/talen: Engels als bijlage per email.

De handleiding is 54,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info