686375
25
Verklein
Vergroot
Pagina terug
1/27
Pagina verder
25
Robot Gun Cleaning Station© Kemppi Oy 2016 1616
OPERATING MANUAL
14. TROUBLESHOOTING
If the measures described below are not successful, please consult your dealer or the manufacturer.
Also consult the operating instructions for the welding components: the welding power source, welding torch system,
re-circulating cooling unit, and so on.
Problem Cause Solution
Compressed-air motor does not run Compressed-air supply or hose connection interrupted
Compressed-air supply or hose connection interrupted
Check all supply lines leading to the cylinder and the ttings
Motor defective; replace
Replace directional valve Y2
Insucient cleaning Milling cutter defective or worn out Replace milling cutter
Welding torch parts damaged Wrong equipment parts Check torch-dependent parts (milling cutter and clamping prism)
Check immersion depth of torch
Table 12: Troubleshooting the injection unit
Problem Cause Solution
No injection Insucient uid level
Compressed-air supply or hose connections
interrupted
Directional valve Y4 does not switch
Add more anti-spatter uid
Check all supply lines leading to the cylinder and the ttings
Replace directional valve Y4
Too much or too little spray mist Metering quantity incorrectly adjusted Change setting of throttle screw
Too little spray mist Injection time too short
Operating pressure too low
Injection time greater than waiting time
Check operating pressure
No spray mist Operating pressure too low Check operating pressure
Table 13: Troubleshooting the wire-cutting device
Problem Cause Solution
No cutting function Compressed-air supply or hose connection interrupted
Directional valve Y3 does not switch
Check all supply lines leading to the cylinder and the ttings
Check signal output of robot control
Replace directional valve Y3
Insucient cutting capacity Too low working pressure
Roughly running slide
Worn cutting edge
Check the adjustment of the pressure regulator: min. 5 bar, max. 8 bar
Unmount movable parts; clean and lubricate them
Clean more often
Change approach position P4
Change the cutter
Free wire end is bent The wire has no contact with the xed jaws
Counter-support jammed
Correct the approach position of the welding torch
Unmount movable parts; clean and oil them
Tighten the mounting screws
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kemppi Robot Gun Cleaning Station bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kemppi Robot Gun Cleaning Station in de taal/talen: Engels als bijlage per email.

De handleiding is 2,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info