686270
21
Verklein
Vergroot
Pagina terug
1/26
Pagina verder
EN
5. Tighten the wire guide in place with the mounting nut.
6. Cut the wire guide 2 mm from the mounting nut and le the sharp edges of the cut round.
7. Reattach the gun in place and tighten the parts to spanner tightness.
3.3 Troubleshooting
Problem cause
The wire does not
move or wire feed
entangles
Feed rolls, wire liner or contact tips are defective
• Check wire mechanism adjustment is not too tight or too loose
• Check that the feed roll groove is not too worn
• Check that the wire liner is not blocked
• Check that the contact tip and wire liner are suitable for the wire size used
• Check that spatter is not blocking the contact tip and that the hole is not closed or damaged
The main switch
indicator will not
light up
• The machine has no supply voltage light
• No electricity connected to the machine
• Check the mains supply fuses
• Check the mains cable and plug
Poor welding results Several factors aect the welding quality
• Check that the wire feed is constant
• Check the trimming settings of welding power control and arc length
• Check the material selection setting
• Check that the earth return clamp is xed properly, xing point is clean, and both cable and its
connections are undamaged
• Check that the shielding gas is suitable for the wire material used
• Check the ow of shielding gas from the tip of the welding gun
• Supply voltage is uneven, too low or too high
Overheating indicator
is illuminated
The machine has overheated
Normally, this indicates that the device has reached its maximum designed operating temperature.
The thermostat has become active, switching the welding power o. Allow the unit to cool and the
machine will soon automatically reset and allow welding to restart.
• Ensure that cooling air has unrestricted ow.
• If the machine’s duty cycle has been exceeded, wait for indicator to turn o.
In certain circumstances, this light may also indicate irregularity in the supply voltage.
Too low or high supply voltage.
If the machine’s malfunction is not eliminated with the above measures, contact Kemppi
service.
3.4 Storage
Store the unit in a clean and dry place. Shield it from rain, and in temperatures exceeding
+25 °C from direct exposure to sun.
3.5 Disposal of the machine
Do not dispose of electrical equipment with normal waste!
In observance of European Directive 2002/96/EC on waste electrical and electronic
equipment, and its implementation in accordance with national law, electrical equipment
that has reached the end of its life must be collected separately and taken to an appropriate
environmentally responsible recycling facility.
The owner of the equipment is obliged to deliver a decommissioned unit to a regional
collection centre, per the instructions of local authorities or a Kemppi representative. By
applying this European Directive you will improve the environment and human health.
19
© Kemppi Oy / 1340
21

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kemppi MinarcMig Evo 170 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kemppi MinarcMig Evo 170 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,18 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Kemppi MinarcMig Evo 170

Kemppi MinarcMig Evo 170 Gebruiksaanwijzing - Nederlands - 26 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info