686381
11
Verklein
Vergroot
Pagina terug
1/26
Pagina verder
EN
Esc button
Use the Esc button to move to the previous menu level.
Displays
• The control panel displays show adjustable operation parameters, their values, and the
units of measure.
• During welding, display P2 shows the welding current value that is currently in use, while
display P6 shows the welding voltage.
Control knobs
• The left-hand control knob P11 allows the adjustment of the speed of wire feeding. The
selected speed is shown on the display on the left-hand side.
• The right-hand side control knob P13 allows for controlling the welding voltage in MIG
and 1-MIG processes, in which case the selected voltage is shown on the right-hand side
display, and the base current in WiseThin processes, in which case the adjustment range
is +/- 50.
These control knobs are also used for specifying the operating parameters. A parameter for
adjustment is selected with the left-hand knob, while the value of the parameter is selected
with the right-hand knob.
2.2.2 Adjusting MIG dynamics (Arc Force)
When you press button P3, you can adjust the MIG welding dynamics of the machine by
means of the right-hand knob.
When using the MIG or 1-MIG welding process, the welding dynamics setting aects the
features of the welding arc and the amount of welding spatter as shown below:
• The value 0 is the recommended basic setting.
• Use values -1...-9 if you want a softer arc and less spatter.
• Use values 1...9 if you want a rougher and more stable arc. This setting is useful when you
are using 100% CO₂ shielding gas when welding steel.
When using a WiseThin process, the welding dynamics setting aects the forming pulse as
shown below:
• Use values -1...-30 if you want a softer arc and smaller penetration.
• Use values 1...30 if you want a rougher and greater penetration.
2.2.3 Gas test
The gas test button P4 opens the gas valve without activating the wire feed or power source.
By default, gas ows for 20 seconds. The gas ow time remaining is shown on the display.
The right-hand knob allows you to set the default gas ow time, between 10 and 60 seconds,
and store the new default value in the machines memory. To stop the gas test, press the ESC
button.
2.2.4 Wire feed test
When you press the Wire inch button, P6, the wire feeder engine starts but the gas valve does
not open and the power source is not activated.
The wire feed pace is 2 m/min for the rst two seconds, and then 10 m/min.
When the button is released, the wire feeding stops. The machine automatically goes back
to the normal state after approximately 3 seconds from release of the button or immediately
when you press the ESC button.
2.2.5 Selection of liquid- or gas-cooled MIG gun
You can select a MIG gun cooled with liquid or gas by pressing buttons P3 and P4
simultaneously and holding them down for at least one second.
• When the display reads GAS, you can use a gas-cooled MIG gun with the equipment.
• When the display reads COOLEr, you can use a liquid-cooled MIG gun with the
equipment.
9
KempArc SYN 300, 400, 500, DT 400 / © Kemppi Oy / 1117
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kemppi Kemparc SYN 300 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kemppi Kemparc SYN 300 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info