598220
438
Verklein
Vergroot
Pagina terug
1/476
Pagina verder
IEEE-488 Bus Overview
G-4 2001-900-01 Rev. K / August 2010
Uniline commands
ATN, IFC and REN are asserted only by the controller. SRQ
is asserted by an external device. EOI may be asserted either
by the controller or other devices depending on the direction
of data transfer. The following is a description of each com-
mand. Each command is sent by setting the corresponding
bus line true.
REN (Remote Enable) — REN is sent to set up instruments
on the bus for remote operation. When REN is true, devices
will be removed from the local mode. Depending on device
configuration, all front panel controls except the LOCAL
button (if the device is so equipped) may be locked out when
REN is true. Generally, REN should be sent before attempt-
ing to program instruments over the bus.
EOI (End or Identify) — EOI is used to positively identify
the last byte in a multi-byte transfer sequence, thus allowing
data words of various lengths to be transmitted easily.
IFC (Interface Clear) — IFC is used to clear the interface
and return all devices to the talker and listener idle states.
ATN (Attention) — The controller sends ATN while trans-
mitting addresses or multiline commands.
SRQ (Service Request) — SRQ is asserted by a device
when it requires service from a controller.
Universal multiline commands
Universal commands are those multiline commands that re-
quire no addressing. All devices equipped to implement such
commands will do so simultaneously when the commands
are transmitted. As with all multiline commands, these com-
mands are transmitted with ATN true.
LLO (Local Lockout) — LLO is sent to the instrument to
lock out the LOCAL key and thus all their front panel con-
trols.
DCL (Device Clear) — DCL is used to return instruments
to some default state. Usually, instruments return to their
power-up conditions.
SPE (Serial Poll Enable) — SPE is the first step in the serial
polling sequence which is used to determine which device
has requested service.
SPD (Serial Poll Disable) — SPD is used by the controller
to remove all devices on the bus from the serial poll mode
and is generally the last command in the serial polling se-
quence.
438

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Keithley 2001 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Keithley 2001 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info