554925
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
UC-261 wireless indoor siren 2 / 2 MFI52702
7. A remote control or doorbell button (RC-4x, RC-22,
RC-28) can be enrolled by pressing the button on the
controller. Multiple pressing of the controller’s button will
allow you to scroll to the desired melody.
8. Detector-chime mode: JA-60 detectors can be enrolled
by inserting batteries into them, one detector at a time. By
triggering the tamper on a detector you can scroll to the
desired melody.
9. Exit programming mode by briefly pressing the button
on the UC-261.
Note:
Up to 8 doorbell buttons or detectors can be used with one
UC-261.
If you enter programming mode the above way, all
previously enrolled devices will be erased from the
UC-261 memory.
Enrolling additional devices
If you want to add additional doorbell buttons or detectors, or
if you want to select another melody for an existing device, then:
1. Unplug the UC-261 from the outlet and wait for 5 seconds.
2. Plug it in again.
3. When the button lights – press it and hold it down. After
hearing a short beep, release the button. The flashing
button indicates that it is in programming mode.
4. Enrolling new devices (or selecting another melody):
A doorbell button or remote control (RC-4x, RC-22,
RC-28) can be enrolled by pressing the button on the
controller. Multiple pressing of the controller’s button will
allow you to scroll to the desired melody.
Detector-chime mode: JA-60 detectors can be enrolled
by inserting batteries into them, one detector at a time. By
triggering the tamper on a detector you can scroll to the
desired melody.
5. Exit programming mode by briefly pressing the button on
the UC-261.
Deleting enrolled devices
Press and hold the button on the UC-261 and plug the
UC-261 into the mains outlet. Two beeps will be heard and all
devices including the control panel will then be erased.
Consequently it is necessary to erase the UC-261 from the
control panel. In control panel enrollment mode scroll to the
UC-261 position, press and hold button 2 until the confirmation
beep can be heard.
Note: If the memory of the UC-261 is deleted but the UC-261 is
not erased from the control panel, then the control panel will
indicate disconnection of the UC-261 from the power but the
UC-261 will not react to signals from the control panel – in
the case of an alarm it will not sound.
Loudness selection
The UC-261 must be in its normal operating mode
(plugged in).
Press and hold the button down.
After 2 seconds you will hear a melody with the new
loudness selected
Release the button.
This way you can toggle between a standard and a quieter
level. This setting does not affect the alarm siren sound.
Power failure
If the UC-261 is disconnected from its power (it is
unplugged or there is a power failure), then a “Low battery”
report will be transmitted to the control panel. In addition if the
system is in alarm mode (the sirens are sounding) the UC-261
will also transmit a “TAMPER“signal.
Doorbell-mode
After pressing a doorbell button, the UC-261 will play a
preselected melody. Different melodies can be assigned to
each doorbell button, if desired. If you want to change a
melody, enter programming mode (see section “Enrolling
Additional Devices”) and press the button until the desired
melody is selected.
Detector-chime mode
If an enrolled detector is triggered, the UC-261 will play a
pre-selected melody. The melody can be changed if desired
(see section “Enrolling Additional Devices”).
A detector enrolled to the UC-261 can be simultaneously
enrolled to a JA-63 or JA-65 control panel. This way, for
example, a wireless door detector can activate a chime on the
UC-261 and at the same time trigger an alarm.
Notes:
1/ The JA-60P motion detector has a special sleep mode
feature (settable to 5 min. or 1 min.). Therefore it cannot detect
more frequent movements in a covered area.
2/ The JA-60SP, JA-60SR fire detectors and JA-60G
cannot be used for chime mode.
Wireless siren mode
The UC-261’s light indicator shows the status of the PgY
output of the enrolled control panel. If an alarm is triggered, the
UC-261 siren sounds. ARM and DISARM chirps can be
enabled or disabled by the following procedure:
1. Unplug the UC-261 from the outlet and wait for
5 seconds.
2. Plug it in again.
3. When the button lights – press it and hold it down.
After hearing a short beep, release the button. The
flashing button indicates that it is in programming mode.
4. On the control panel in P mode enter 299 repeatedly to
toggle between these two settings:
When one beep is heard, no chirps will be performed by
the UC-261.
When two beeps are heard, both ARM and DISARM
chirps will be performed by the UC-261.
Note: Although this product does not contain any
harmful materials we suggest you return the product to
the dealer or directly to the producer after use.
Internet: www.jablotron.cz
Tel.: +420 483 559 999
fax: +420 483 559 993
Pod Skalkou 33
466 01 Jablonec nad Nisou
Czech Republic
UC-261 wireless indoor siren 2 / 2 MFI52702
7. A remote control or doorbell button (RC-4x, RC-22,
RC-28) can be enrolled by pressing the button on the
controller. Multiple pressing of the controller’s button will
allow you to scroll to the desired melody.
8. Detector-chime mode: JA-60 detectors can be enrolled
by inserting batteries into them, one detector at a time. By
triggering the tamper on a detector you can scroll to the
desired melody.
9. Exit programming mode by briefly pressing the button
on the UC-261.
Note:
Up to 8 doorbell buttons or detectors can be used with one
UC-261.
If you enter programming mode the above way, all
previously enrolled devices will be erased from the
UC-261 memory.
Enrolling additional devices
If you want to add additional doorbell buttons or detectors, or
if you want to select another melody for an existing device, then:
1. Unplug the UC-261 from the outlet and wait for 5 seconds.
2. Plug it in again.
3. When the button lights – press it and hold it down. After
hearing a short beep, release the button. The flashing
button indicates that it is in programming mode.
4. Enrolling new devices (or selecting another melody):
A doorbell button or remote control (RC-4x, RC-22,
RC-28) can be enrolled by pressing the button on the
controller. Multiple pressing of the controller’s button will
allow you to scroll to the desired melody.
Detector-chime mode: JA-60 detectors can be enrolled
by inserting batteries into them, one detector at a time. By
triggering the tamper on a detector you can scroll to the
desired melody.
5. Exit programming mode by briefly pressing the button on
the UC-261.
Deleting enrolled devices
Press and hold the button on the UC-261 and plug the
UC-261 into the mains outlet. Two beeps will be heard and all
devices including the control panel will then be erased.
Consequently it is necessary to erase the UC-261 from the
control panel. In control panel enrollment mode scroll to the
UC-261 position, press and hold button 2 until the confirmation
beep can be heard.
Note: If the memory of the UC-261 is deleted but the UC-261 is
not erased from the control panel, then the control panel will
indicate disconnection of the UC-261 from the power but the
UC-261 will not react to signals from the control panel – in
the case of an alarm it will not sound.
Loudness selection
The UC-261 must be in its normal operating mode
(plugged in).
Press and hold the button down.
After 2 seconds you will hear a melody with the new
loudness selected
Release the button.
This way you can toggle between a standard and a quieter
level. This setting does not affect the alarm siren sound.
Power failure
If the UC-261 is disconnected from its power (it is
unplugged or there is a power failure), then a “Low battery”
report will be transmitted to the control panel. In addition if the
system is in alarm mode (the sirens are sounding) the UC-261
will also transmit a “TAMPER“signal.
Doorbell-mode
After pressing a doorbell button, the UC-261 will play a
preselected melody. Different melodies can be assigned to
each doorbell button, if desired. If you want to change a
melody, enter programming mode (see section “Enrolling
Additional Devices”) and press the button until the desired
melody is selected.
Detector-chime mode
If an enrolled detector is triggered, the UC-261 will play a
pre-selected melody. The melody can be changed if desired
(see section “Enrolling Additional Devices”).
A detector enrolled to the UC-261 can be simultaneously
enrolled to a JA-63 or JA-65 control panel. This way, for
example, a wireless door detector can activate a chime on the
UC-261 and at the same time trigger an alarm.
Notes:
1/ The JA-60P motion detector has a special sleep mode
feature (settable to 5 min. or 1 min.). Therefore it cannot detect
more frequent movements in a covered area.
2/ The JA-60SP, JA-60SR fire detectors and JA-60G
cannot be used for chime mode.
Wireless siren mode
The UC-261’s light indicator shows the status of the PgY
output of the enrolled control panel. If an alarm is triggered, the
UC-261 siren sounds. ARM and DISARM chirps can be
enabled or disabled by the following procedure:
1. Unplug the UC-261 from the outlet and wait for
5 seconds.
2. Plug it in again.
3. When the button lights – press it and hold it down.
After hearing a short beep, release the button. The
flashing button indicates that it is in programming mode.
4. On the control panel in P mode enter 299 repeatedly to
toggle between these two settings:
When one beep is heard, no chirps will be performed by
the UC-261.
When two beeps are heard, both ARM and DISARM
chirps will be performed by the UC-261.
Note: Although this product does not contain any
harmful materials we suggest you return the product to
the dealer or directly to the producer after use.
Internet: www.jablotron.cz
Tel.: +420 483 559 999
fax: +420 483 559 993
Pod Skalkou 33
466 01 Jablonec nad Nisou
Czech Republic
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron UC-261 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron UC-261 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,26 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info