554913
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Wireless Control Receiver UC-216 2/2 MEJ52103
Operating of the remote control in this mode is as follows:
pressing button A while both UC-216 relays are off, the relay X will
be activated for 2 minutes
pressing button B while both UC-216 relays are off, the relay Y will
be activated for 2 minutes
pressing any remote control button while any UC-216 relay is on,
will switch off this relay.
Up to 20 remote controls can be enrolled to this mode, using the
method above. After the first remote control is enrolled to this special
mode, no other UC-216 learning mode will be available.
Use of the UC-216 with JA-60 detectors
All wireless JA-60 detectors can be
used with the UC-216. In such a case the
UC-216’s outputs have the following
functions:
relay X alarm trigger (detector output)
relay Y tamper output (tampering of a
detector or the signal that
a detector was lost) - all
detectors are supervised
OUT low battery signal from
a detector
A maximum of eight JA-60 detectors can be enrolled into a single UC-
216’s memory. The UC-216’s outputs will react to all enrolled detectors.
For example if any enrolled detector has an opened cover, the UC-
216’s Y relay will be activated.
The X relay reacts to all types of signals from a JA-60 detector (INST,
DELAY, FIRE, PANIC). For example, the selection of INST or DELAY
reaction in a JA-60P makes no difference to the function of the UC-
216’s output ( the relay will be activated instantly when any movement is
detected).
Enrolling of JA-60 detectors
Detectors can be enrolled to a UC-216 only if all other items (remote
controls) have been erased from the UC-216’s memory. The detectors
can be enrolled the following way:
remove the batteries from the JA-60 detector
select learning mode no. 1 for relay X in the UC-216
install batteries into the detector
the UC-216 will automatically store the detector’s code into its memory
close the cover of the JA-60 detector
By repeating this procedure you can teach up to eight JA-60 detectors
to each UC-216.
After the first JA-60 detector is enrolled, no other item will be possible
to enroll other than additional JA-60 detectors.
Use of the UC-216 with a JA-60D keypad
JA-60D keypads can be used with the
UC-216. In such a case the UC-216’s
outputs have the following functions:
relay X will change its status after a
valid access code is entered
on the keypad (on - off - on
...). The relay can also be
switched on by entering F1 on
the keypad (a quick arm
function).
relay Y is a tamper output (tampering of a keypad, more than 5
unsuccessful attempts to enter a valid access code or the
signal that the keypad was lost) - all keypads are
supervised
OUT low battery signal from a keypad
A maximum of eight JA-60D keypads can be enrolled into a single
UC-216’s memory. The UC-216’s outputs will react to all enrolled
keypads. For example if any enrolled keypad has an open cover, the
UC-216’s Y relay will activate.
Enrolling of the JA-60D keypad
The JA-60D keypads can be enrolled to a UC-216 only if all other
items (remote controls, detectors) have been erased from the UC-216’s
memory. The keypad can be enrolled the following way:
remove the battery from the JA-60D
select learning mode no. 1 for relay X in the UC-216
install the battery into the keypad
The UC-216 will automatically store the keypad’s code into its
memory
close the cover of the JA-60D keypad
By repeating this procedure you can teach up to eight JA-60D
keypads to each UC-216.
After the first JA-60D keypad is enrolled, no other item will be able to
be enrolled other than additional JA-60D keypads.
Supervising Detectors and Keypads
All enrolled JA-60 detectors (or keypads) transmit regular testing
signals. If the UC-216 does not receive this testing signal from any
enrolled detector (keypad) for a period longer than 1 hour, relay Y will
be triggered (tamper output).
This supervising function can be disabled by disconnecting the JP1
jumper in the UC-216.
Note: If the JP1 link is open, supervising is disabled and all of the UC-
216’s outputs (X, Y and OUT), will have a 2 second pulse reaction to
signals from detectors or keypads. In the contrary, when the JP1 is closed,
all of the UC-216’s outputs are copying the status of the detector (for
example, the Y relay is activated for the entire period in which a detector
or a keypad is open, etc.) and entering of the access code on the keypad
will change the condition of the relay X (on - off - on...).
Use of the UC-216 with the JA-60K control panel.
The UC-216 can also be used as a
wireless output module for the JA-60K
control panel. The UC-216's X and Y
output relays will have the same functions
as the PgX and PgY programmable
outputs of the control panel (see JA-60
installation manual for more details). The
OUT output will indicate if the JA-60
system has any problem with power (low
battery in items, failure of AC etc.).
To use the UC-216 with the control
panel, all other items have to be erased from the UC-216’s memory.
The control panel can be enrolled the following way:
enter the programming mode on the JA-60K
select learning mode no. 1 for relay X in the UC-216
enter the code 299 on the JA-60K keypad
The UC-216 will automatically store the control panel’s code in its
memory
exit the JA-60K’s programming mode
Up to eight JA-60K control panels can be enrolled to each UC-216.
After the first JA-60K is enrolled, no other item will be able to be
enrolled other than additional JA-60K control panels.
Erasing items from the UC-216’s memory
All enrolled remote controls (or JA-60 items) can be erased from the
UC-216’s memory. Open the cover and press both setting buttons and
hold them pressed until all indicators flash for a moment. The UC-216‘s
memory will now be erased.
Note: Although this product does not contain any harmful materials we suggest
you to return the product to the dealer or directly to the producer after usage.
fax: 420 483 559 993
tel.: 420 483 559 999
www.jablotron.cz
export@jablotron.cz
Po d Skalko u 3 3
466 01 Jablonec nad Nisou
Czech Republic
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron UC-216 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron UC-216 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info