554913
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Wireless Control Receiver UC-216 1/2 MEJ52103
Wireless Control Receiver UC-216
Description
The UC-216 is a three channel receiver of coded radio signals. The status
of its two output relays and its output transistor is indicated on the front
panel. Up to 20 remote controls (RC-11, RC-22) can be taught to the unit.
There are three different operating modes available for the remote controls.
This allows the UC-216 to be used as a control for an alarm system, for
remote gate opening, garage door control, panic switch etc. A floating code
ensures a high security of transmission.
The UC-216 can also be used as a receiving unit for JA-60 wireless
system items. This use, for example, allows an existing wire-operated alarm
system to be extended with additional wireless detectors, wireless access
control keypads, etc.
Specifications:
Operating voltage: 12-24 V DC or 15 V AC
Power consumption: standby 0.25 W
max. 1 W (both relays activated)
Operating frequency: 433.92 MHz
Coding: digital, each remote control or JA-60 item has
a unique floating code
Output relays: Max. 120 V / 1 A
Output transistor: Max. 40 V / 0.2 A
Range (open area) : with RC-11 up to 30 meters
with JA-60 items, up to 100 meters
Working temperature from -10 to +40°C indoor use only
Can be operated according to ERC REC 70-03
Hereby, Jablotron Ltd., declares that this UC-216 is in compliance with
the essential requirements and other relevant provisions of Directive
1999/5/EC.
Original of the conformity assessment can be found at the web page
www.jablotron.cz, section Technical support.
Installation:
Open the external cover of the unit by pressing in the internal tab of
the lock on the top (small flat screw-driver is appropriate). Loosen the
central screw and remove the PCB. Route the wires through the hole in
the bottom of the rear housing. Attach the housing to the desired place
using the provided screws.
Terminals description:
TAMPER tamper switch output (max. 24 V / 100 mA)
OUT output of NPN transistor to GND
NC, NO, C output relay dry contacts (X and Y)
+U, GND power voltage 11-24VDC or 15VAC
The status of relay X, relay Y and the OUT is indicated by 3 LED
indicators on the front cover. When active, the corresponding LED
lights.
RC-11, RC-22 mode
Remote controls enrolling - you can
enroll up to 20 different RC-11 or RC-22
remote controls to the UC-216 unit. There
are two buttons on each remote control
(A and B), enabling each remote control
to send two different commands by
pressing button A or B. The RC-11 can
also send a third command by pressing
the A & B button simultaneously (not
available with the RC-22).
There are two setting buttons in the
UC-216. Button X is used for relay X
teaching; button Y is used for relay Y
teaching. By pressing the setting button
you can scroll through the three learning
(operating) modes (1 to 3) indicated by a
corresponding flashing indicator.
By pressing a button on the remote
control while a desired UC-216 learning
mode is selected, you enroll that button to
the receiver’s memory. The corresponding
operating mode will now be associated
with this remote control button.
Operating modes available (valid for X and Y relays)
MODE reaction of the relay
when RC button pressed
which RC
button can be
taught
1 pulse
relay will turn on for 2 seconds A, B, A&B
2 latch
relay status will change to the
opposite (ON/OFF/ON...)
A, B, A&B
3 ON - OFF
button A turns relay on, button B
turns relay off
A or B
Setting remarks
new RC button enrollments are added to previously enrolled ones
after 20 RCs are taught, no other remote can be added
double flashing of the LEDs indicates a full memory
if one button is taught for multiple modes, only the last taught mode
will remain in the UC-216’s memory
you can combine different modes with different RC buttons
the output OUT can be activated only by simultaneous pressing of
the A&B buttons on the RC-11, only if the A button was enrolled for
relay X and the B button for relay Y. The OUT mode is the same as
the selected mode of relay X. This way three independent outputs
can be controlled.
A selected setting mode will close after an RC button is enrolled,
or automatically after 10 seconds.
All UC-216’s can operate with only remote controls or JA-60 items.
Combined operation is not available.
Note: A remote control taught to the UC-216 can also be used for
other devices. For example: the remote control of Jablotron’s Accent car
alarm can not only control your car with buttons A and B, but can also
control another device, if the simultaneous pushing of A&B buttons has
been taught to a UC-216 controller.
Garage door or gate opener mode
The UC-216, in combination with RC-11
or RC-22 remote controls, has an optional
mode to control garage door or gate
actuators. This mode is only available when
the UC-216’s memory is erased. By
pressing the UC-216’s X setting button,
scroll until both LED’s 1 & 2 are
simultaneously flashing. Then, by pressing
any button of the remote control, you teach
it to the UC-216.
A
B
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron UC-216 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron UC-216 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info