554896
4
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
Telephone dialer TD-101 / TD-101W - 4 - MDJ512 10 Telephone dialer TD-101 / TD-101W - 21 - MDJ512 10
3. TD-101 includes
the dialer, 2.5m telephone cable, set of screws, manual, and
emergency
F button marking label. Model TD-101W, in
addition, includes a wireless remote control (RC-10)
4. Installation
We recommend professional installation of the dialer. The
dialer should be fixed in the desired location using the two
included screws (see drilling diagram at the end of this manual).
First, partially screw in the top screw and slide the screw head
through the hole in the upper part of the TD-101 rear panel. Then
open the dialer terminal compartment cover and mark the position
of the second screw. Place cables through the hole for cables in
the rear panel before installing the second screw. Do not open the
upper part of TD-101 housing during installation; doing so will
result in voiding of warranty.
4.1. Terminal Description
IN telephone line input (inlet of the telephone line to
the house)
OUT telephone line output (phone, fax etc.); in the stand by mode the line operates as normal. If
triggered, the TD-101 will use the line (switch off the other devices)
+12V, GND external power supply (12VDC, max. 100mA)
TAMPER tamper switch (normally closed contacts)
IN1 +/- positive and negative poles of the first trigger input
IN2 +/- positive and negative poles of the second trigger input
Both TD-101 trigger inputs have built in opto-
couplers. The dialer is triggered when an opto-
coupler current is switched on (factory default),
opposite logic of inputs is programmable (trigge-
ring by the current switching off). There are
many possibilities on how to connect the trigger
inputs - see examples on page 20. Consider
that the dialer reacts only to signals with a
duration of 0.1sec. or longer. Each optocoupler
is ON only if its input terminal voltage is 5 to
20V.
5. Operation
When power is supplied, the dialer will perform an automatic self test (red LED turns on for
10 seconds). Then the TD-101 will enter the stand by mode. In this mode, the TD-101 is waiting for an
input form either the keypad or the trigger inputs. For correct function of the dialer, the telephone
numbers and messages must first be programmed (see chapter 6.).
5.1. What does the dialer do if activated:
seizes the telephone line (switches off all other devices)
checks dial tone, if the tone is not detected, it will try to release the line again
dial the first tel. number and if detects:
ringing tone, it will send the message and will not call this number again
busy signal, it will call next number and then will try to call the previous number again
The red LED will light when the dialer has been triggered. Once the dialer has been triggered, it's dialing
procedure can be terminated by pressing and holding the
E key (if enabled in installer level). This is
possible only when the IN1 and IN2 inputs are not triggered.
11.3. Example of TD-101(W) use with different alarm systems
Suggestion of programming for the configuration above
tel. number memories
Mem
1, 2 - not used
user mode
3, 4 - numbers for alarm voice message
setting
5 - not used
6 - alarm PAGER number and data
record only voice mess. no. 2
data for Monitoring Station
four report codes disarming
installer
mode
can be programmed arming
setting
(see chapter 8) alarm
end of alarm
logic of IN1 and IN2 inputs Normally Closed contacts
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron TD-101 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron TD-101 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info