Handleiding Jablotron TD-101 (pagina 12 van 12) (Engels)

554896

Verklein

Vergroot

Pagina terug

1/12

Pagina verder

Telephone dialer TD-101 / TD-101W - 12 - MDJ512 10 Telephone dialer TD-101 / TD-101W - 13 - MDJ512 10

7.7. Testing the Monitoring Station communication

Communication to the MS can be tested in the installer mode (the yellow LED is ON - see 7.1.), entering:

where:

is the tel. number memory 7 or 8 which will be called

means event number (3, 4, 5 or 6) which code will be sent (see item 7.6.)

Example: Report code corresponding to IN2 input triggering (activation) will be sent to the main tel. number :





8. Optional functions and parameters programming

The settings chosen in the Installer mode can significantly customize the dialer operation. This

programming should be done by a professional installer.

8.1. Opening of Installer Mode for Optional functions programming

To enter Installer level from the Standby, enter Installer code IC press

and enter Installer

Code IC again. Factory default IC is 1010 so when you open the Installer mode for the first time,

enter



. The installer level is indicated by the yellow LED.

All parameters are programmed in the sequences started with

Fkey. If a sequence is entered, the

red LED will start to flash. When the sequence is completely entered, the red LED will turn off (data

will be stored). A started sequence entering can also be terminated by pressing the

Ekey at any

time.

After all programming, the Installer mode must be exited by pressing the

Ekey (all the LEDs will turn

off). The dialer can not be activated in the Installer level !

Note: The installer code IC can also be used to open the user level, the same way as the User Code.

8.2. Dialing method

Pulse or tone dialing can be selected in the Installer mode (the yellow LED is ON - see 8.1.),

entering:

D

where:

= 0 pulse

= 1 tone (factory default)

The dialing method can also be changed from pulse to tone by entering Finside the phone number (it

will insert a pause and it will switch to tone dialing); the

Fkey can not be stored as the first digit.

Example: tone dialing will be selected



8.3. Number of voice messages

One or two voice messages can be selected in the installer mode (the yellow LED is ON - see 8.1.),

entering:

D

where:

D means number of messages 1 = 1x 20sec. or 2 = 2x 10sec.

(factory default = 2 messages, max. 10sec. each)

If only one message is selected (max. 20sec.) :

• it should be recorded as message no. 1

• IN1 triggering will send the message to

Mem1 and Mem2

• IN2 triggering will send the message to

Mem3 and Mem4

• simultaneous triggering of IN1 and IN2 will send the message to all

Mem1 to Mem4 tel. numbers

• Pager and monitoring station communications will not be effected

• to play the message in stand by press only the

Mkey

Example: Only one voice message, max. 20sec. will be selected :



8.4. Trigger inputs IN1 and IN2 logic

The method of IN1 and IN2 triggering can be selected in the installer mode (the yellow LED is ON -

see 8.1.), entering:

D

where:

= 0 inputs are triggered if the input optocoupler current is switched off (N.C. trigger)

= 1 input is triggered if the input optocoupler current is switched on (N.O. trigger)

(factory default setting is 1 = N.O. trigger)

Example: IN1 and IN2 will react to switching the current off (suitable for Normally Closed contacts)



8.5. Trigger delay

The dialer reaction delay can be programmed in the Installer mode (the yellow LED is ON - see 8.1.),

entering:

D 



D can be from 0 to 9, it means that the duration of the delay x10sec (i.e. 0 to 90sec.). Dialing

will start with the delay only if the corresponding Input is triggered longer than the selected

delay. If the input is deactivated before the delay time elapses, the dialer will not work. The delay

is valid for all voice, Pager and Monitoring Station dialing.

Note: triggering with

Fkey or with the remote control (TD-101W) will always have no delay.

(factory default setting is no delay = instant reaction)

Example: Delay 30sec. will be selected :



8.6. Number of cycles to send voice & Pager messages

Number of attempts to call each number can be selected in the installer mode (the yellow LED is ON

- see 8.1.), entering:

D

D means number of cycles, can be 1, 2 or 3. One cycle means sending of the corresponding

messages to all stored phone numbers in the

Mem1 to Mem6 memories

(factory default setting are 3 cycles)

Example: Two cycles will be selected :



Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Jablotron TD-101 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info