554793
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
The JK-82 / JK-82UK “Oasis” wireless alarm kit 2/2 MKE58102
2. Install the JA-80P PIR motion detector about 2 to 2.5 meters above
the floor, select its reaction via the relevant internal DIP switch
(INS/DEL), connect its battery up and close the cover.
tab
3. Plug the JA-80L siren into a mains power socket
4. Test and install the RC-89 door bell button.
5. Enrolling more wireless devices
The system can be extended with more wireless devices (a maximum of
50 can be enrolled). To enroll another device, the CP should be in service
mode, if it is not enter 0 8080 (while the system is unset)
1. On the keypad, key in 1 to enter enrollment mode
2. The next vacant address is displayed (scroll to other addresses
using the arrow keys if desired)
3. Connect up the device’s battery to enroll the device to the CP.
Successful enrollment is confirmed by the A indicator lighting. The
next vacant address is then displayed.
The RC-86 key-fob can also be enrolled by pressing and holding a
pair of its buttons + (or
+ )
4. Exit enrollment mode by pressing the # key.
To enroll the CP to UC-82 or AC-82 modules, enter 299 while the
CP is in service mode with the receiving module in enrollment mode.
6. Testing device functionality
1. The CP should be in Service mode, if not enter 0 8080
2. First trigger the device under test (e.g. a detector). The keypad
(with its flip cover open) then indicates triggering of the device if the
device is functioning correctly and is enrolled.
Motion detectors are best tested within 15 minutes of closing their
covers as after that they only react to frequent movements once
every 5 minutes (to restart a device’s test mode, open and close the
detector housing again).
7. Checking a device’s radio signals
1. The CP must have its antenna connected and should be in Service
mode, if not enter 0 8080
1. Enter 298, the lowest address with enrolled device will be displayed
2. Trigger the device linked to this address – the keypad (with its flip
cover open) then shows the device’s signal strength in the range ¼
to 4/4 (it should be at least 2/4, if not, relocate the device)
Motion detectors are best tested within 15 minutes of closing their
covers as after that they only react to frequent movements once
every 5 minutes (to restart a device’s test mode, open and close
the detector housing again).
To test the JA-80F keypad signal, trigger the connected magnetic
door sensor or activate the keypad’s tamper sensor.
To test the JA-80L siren signal, press the siren’s button.
3. To select the next enrolled device address use the arrow keys.
4. To exit signal measurement mode, press the # key.
8. Programming the system
1. The CP should be in Service mode, if not enter 0 8080
2. Enter the appropriate programming sequences to select the desired
functions (a complete list of them is in the CP and communicator
manuals)
Function Sequence Note
New service code
5 xxxx
xxxx
Factory default: 8080
xxxx = new code
Exit delay 20x
x=multiples of 10 sec. (e.g. 205 = 50
sec).
Factory default: 30s
Entrance delay 21x
x=multiples of 5 sec. (e.g. 204 = 20
sec.).
Factory default: 20s
Alarm duration 22x
x=1 to 8=1 to 8 minutes
9 = 15min.
Factory default: 4 min
Tel. numbers for event
reporting to telephones
81 M xx.x
0
M = memory 1 to 8
Factory default reports:
M1 & 2 alarms by SMS
M3 & 4 alarms by SMS+call
M5 & 6 alarms by SMS+call &
setting/unsetting by SMS
M7 alarms by call
M8 faults by SMS
xx..x = tel. number
81 M 0 erases memory M
Forwarding of incoming
SMSes to the first
programmed phone
number
926 x
x = 1 enabled (factory def.)
x = 0 disabled
Registration code for
www.GSMlink.cz
to
your mobile phone
910 xx.x 0
xx.x =your mobile number
Time and date entry 4 hh mm DD MM YY
9. Testing GSM communication
1. Program your mobile phone number to memory M1
2. Exit Service mode via the # key and press both buttons on the key-fob
to trigger a Panic alarm – an alarm SMS should be sent to your mobile.
3. End the Panic alarm by pressing the button on the key-fob.
4. Call the SIM card number (it is shown in the alarm SMS report). Wait
until the call is answered by the CP (beep in the phone) and enter a valid
service code (factory default: 8080)
5. Your phone keypad should now work the same way as the system
keypad – test it.
6. End the call
7. Erase your mobile’s number from M1 and program it into M8 if you wish
to receive reports of technical troubles in the system in future.
10. Editing keypad text strings
1. The CP should be in Service mode, if not enter 0 8080
2. Press and hold the ? key to enter editing mode.
3. Keys: 1 & 7 scroll through characters and numbers
4 & 5 move the cursor
2 erases the highlighted character
& are for the selection of text strings
# exits editing mode
Editing text only affects the text in that particular keypad. A more
convenient way of text editing is with a PC running Olink software.
11. Finishing off the installation
1. Exit service mode via the # key and demonstrate clearly how to
operate the system to the user(s).
2. Recommend the user to change the default master 1234 code to
a new master code.
Entry Function
code / card Setting/unsetting (arming and disarming)
ABC Complete arming (all sections)
A Partially setting A (if used)
B Partially setting AB (if used)
4
Reading the event memory (4 scrolls backwards)
5
Changing the MASTER code/card (e.g. *5 1234 2789 2789)
6
To create a new user code/card (e.g. *6 1234 03 3344
programs user code number 3, to erase the code enter: *6
1234 03 0000)
7 code/card
To secretly signal operation (unsetting) under duress
8 a 9
PGX and PGY control (if used)
0 MASTER
code
Maintenance mode (testing, overview of codes, bypassing,…)
# Exiting maintenance mode or terminating an incomplete entry
?
Displays status details (triggered detectors, fault causes or
the status of PG outputs …..)
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron JK-82 Oasis bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron JK-82 Oasis in de taal/talen: Engels als bijlage per email.

De handleiding is 0,14 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Jablotron JK-82 Oasis

Jablotron JK-82 Oasis Gebruiksaanwijzing - Deutsch - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info