554793
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
The JK-82 / JK-82UK “Oasis” wireless alarm kit 1/2 MKE58102
The JK-82 / JK-82UK “Oasis” wireless alarm kit
Installation of the JK-82 kit shall only be undertaken by technicians holding
a certificate issued by an authorized distributor. This simplified installation
manual only describes the basics, for more details see the manuals of
particular devices.
1. Factory-default pre-enrolled devices
Address Device Note
03 JA-81M door detector
Delayed reaction
04 JA-80P PIR detector
Delayed reaction
48 RC-86 keyfob
Buttons
and
pre-enrolled
49 JA-80F keypad unit
Connect a magnetic door
sensor to its IN input
50 JA-80L indoor siren
RC-89 doorbell button*
Pre-enrolled to the JA-80L
* The RC-89 doorbell button is not delivered with the JK-82UK
2. Before installation
Have a SIM card ready for the GSM communicator which is
activated and does not require a PIN code to register to a GSM
network. If it is a prepaid card it should be sufficiently topped up.
3. Control panel and keypad installation
1. Attach the Control Panel (CP) to the desired location
2. Insert the SIM card into the communicator’s SIM card holder.
3. Connect back-up battery to the CP (attach it securely with
adhesive tape).
4. Connect the mains to the CP – its green LED will start flashing
5. The communicator’s red LED should be lit during registration to
the GSM network, and should turn off within 1 minute. If it
starts flashing instead, turn off the power (mains & battery) and
check that the SIM card functions properly in a mobile phone.
6. Connect up the batteries in the JA-80F keypadservice
mode should be displayed (if not, disconnect the keypad
batteries, check that the control panel is powered up and
reconnect the keypad batteries).
Keeping the key pressed while connecting the keypad
batteries will open the keypad’s internal menu which allows
you to select the desired language (English = 1), to exit this
menu press the # key.
If you exit Service mode accidentally, it can be re-entered by
keying in 0 8080.
Close the keypad’s flip cover to save the battery while in the
service mode
7. Key in 98101 - to set texts of the communicator to English
language
8. Enter 922 to measure the GSM signal – it should be at least
2/4 (if it is not, find another location for the control panel or try
another provider’s SIM card).
9. Exit GSM measurement mode by pressing the # key.
10. Before attaching the JA-80F keypad, test that it functions
correctly at the desired location. We recommended wiring up a
magnetic door sensor (provided with the kit) to the keypad’s IN
input. This will ensure that the keypad is “woken up” whenever
the door is opened (to indicate system status, to make entrance
delay beeps and to have the access card reader ready for
reading cards).
4. Installing the detectors and the siren
1. Install the JA-81M magnetic detector, select its reaction via the
internal DIP switch (INS/DEL), connect its battery up and close
the cover.
IN 2
IN 1
GND
TMP
1k
mag.senzor
ON/OFF
Reaction
tamper
switch
external
senzor
Communicator
Main board
Transformer
Back-up battery
Mains terminal
Digital bus connector
GSM antenna
Tamper switch
SIM card
LEDs
RESET
12 34
ON
OFF
Antenna
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron JK-82 Oasis bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron JK-82 Oasis in de taal/talen: Engels als bijlage per email.

De handleiding is 0,14 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Jablotron JK-82 Oasis

Jablotron JK-82 Oasis Gebruiksaanwijzing - Deutsch - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info