Handleiding Jablotron JA-83K (pagina 6 van 22) (Engels)

554836

Verklein

Vergroot

Pagina terug

1/22

Pagina verder

g) check whether the keyboard functions in the place where you

intend to install it and then install its plastic rear part.

*) The keypad comes with English texts from production – these can be

changed to other languages – see the manual.

Note: If the “Service” message fails to appear on the connected wired keypad

or if the wireless keypad is not enrolled, the control panel settings are not the

factory-defaults – perform a reset (see 3.8.)

JA-83K control panel installation manual - 6 - MKG51101

5 OASiS wireless devices

The control panel had 50 addresses (01 to 50), allowing the enrollment

of up to 50 wireless devices (detectors, keypad, key fobs, sirens etc.). A

device can be assigned to an address either by enrollment or by typing its

serial number while in Service mode (see 6.42).

Wireless devices can be installed at their intended locations and then

enrolled to the control panel or vice versa. If there are any doubts as to the

suitability of devices for communication, temporarily attach the devices (e.g.

using adhesive tape) in the selected place and test radio communication

before finalizing installation. Follow the manuals of the particular devices

during their installation.

5.1 Enrolling wireless devices to the control panel

1. The control panel must be in Service mode. If this is not the case,

enter *0 service code (factory default: 8080). The control panel must be

disarmed.

2. Press the “1” key to enter enrollment mode. The first vacant

address is then offered.

3. You can select the desired address using the 1 and 7 keys (If

the address is already occupied, the A indicator is lit),

4. The device can be enrolled to the selected address by connecting its

battery (power),

5. Enrollment to the given address is confirmed by the A indicator and

the next vacant address is then offered,

6. Enrol all devices to the control panel one after another by connecting

batteries to them. Press the # key to exit enrollment mode.

Notes:

 Enrolment of a wireless device to an address disables the

corresponding hard-wired input terminal (when the device is

erased, the terminal is enabled again).

 RC-8x type key fobs are enrolled to the control panel by pressing and

holding two buttons at the same time: + or + . This means

that a 4-button key fob can be enrolled to the control panel as two

different pairs of buttons and different features can be assigned to

them – see 6.40,

 Only a single device can be enrolled to each address,

 When an address is occupied (the A indicator lights), no more new

devices can be enrolled to it,

 If a device has already been enrolled to an address, and it is then re-

enrolled to another address, the device’s address assignment changes

from the original address to the new one,

 If a device cannot be enrolled to the control panel, it does not have a

good connection to the control panel (the device must be at least 2 m

away from the control panel and an antenna must be connected to the

control panel during enrollment),

 To re-enroll a device, first disconnect its battery. Then wait about 10

seconds (or, to save time, press and release the tamper switch on the

device), before you switch it on again

 A sub-control panel can be enrolled to a master control panel by

keying in the sequence “299” on the keypad of the sub control panel

which must be in Service mode,

 If you intend to use the final door function, the final door detectors

must be enrolled to addresses from 01 to 05 or from 46 to 50 (see

6.22)

5.2 Testing enrolled wireless devices

1. The control panel must have its antenna connected and it must be in

Service mode (If this is not the case, enter *0 service code (factory

default: 8080). The control panel must be disarmed),

2. Trigger the device to be tested (if it is a detector, close its cover first

and then wait until it is ready for testing),

3. The keypad (its cover should be flipped open) beeps and displays a

description of the signal received from the device under test

4. You can test the enrolled devices one after another by activating them

one by one. You can carry the wireless keyboard with you during the

inspection.

Notes:

 JA-80P and JA-85P motion detectors can be tested max. 15 minutes

after closing their cover. After that the detectors ignore frequent

movements (see the detector manual),

 Devices can also be tested in Service mode – see 7.4.

5.3 Signal strength measuring

1. The control panel must have its antenna connected and it must be

in Service mode (If this is not the case, enter *0 service code (factory

default: 8080). The control panel must be disarmed),

2. Key in 298, and the lowest enrolled device address is displayed

3. Trigger this device. The keypad (its cover should be flipped open)

displays signal quality ranging from 1/4 to 4/4,

4. Use the 1 and 7 keys to select other enrolled devices and

measure their signal strengths,

5. Exit signal measuring by pressing the # key

Notes:

 The JA-80P and JA-85P motion detectors can be tested max. 15

minutes after closing their cover. After that the detector ignore frequent

movements (see the detector manual),

 Measuring the signals from the JA-80L internal siren can be activated

by pressing its button. The JA-80A outdoor siren and wireless keypad

signal can be measured by triggering the IN input or triggering its cover

tamper switch,

 Each installed device should have the minimum signal strength of 2/4.

If the signal is too weak, the device should be relocated or higher

control panel sensitivity can be selected. (see 6.36) Alternatively, the

control panel can be equipped with an external antenna.

 This measurement shows the strength of the signal received from the

device by the control panel.

 The wireless keypad can be carried during device testing, its tamper

contact can be disabled via the jumper (near the tamper contact – do

not forget to re-enable the tamper upon finishing the servicing) – Note:

the keypad usually has a slightly shorter communication range than the

detectors. Therefore, if carried to more-distant detectors the triggering

of the detectors might not be shown.

 The most convenient way of measuring is via a computer using OLink

SW.

5.4 Erasing enrolled devices

1. The control panel must be in Service mode. If this is not the case,

enter *0 service code (factory default: 8080). The control panel must be

disarmed,

2. Key in “1” to enter enrollment mode and select the desired address

of the device you wish to erase using the keys 1 and 7 ,

3. Press and hold the “2” key until a beep is heard and the A indicator

turns off,

4. When all the desired devices have been erased press #.

Notes:

 To erase all wireless devices, press and hold the “4” key in enrollment

mode,

 If a wireless keypad is erased by the above mentioned means, it stops

communicating with the control panel and you must re-enrol it again

(see 3.4).

5.5 Enrolling the control panel to UC and AC

modules

If you wish to transmit PGX and PGY programmable output signals to the

UC-82 and AC-82 output modules, you must enroll the control panel to these

modules as follows:

1. The control panel must be in Service mode. If this is not the case,

enter *0 service code (factory default: 8080). The control panel must be

disarmed,

2. Enter the control panel enrollment mode on the UC or AC module

(see the manual of the particular module),

3. Key in 299 on the control panel keypad – the LEDs on the module will

flash a few times.

Notes:

 we recommend locating the module close to the control panel during

enrollment or carry the wireless keypad close to the module,

 the control panel can be enrolled to the desired number of UC/AC

modules (each PG output can thus have an output at an arbitrary

number of places in the house),

 PG outputs are enrolled to UC and AC module relays individually (PGX

output to the X relay, PGY output to the Y relay). This means that

either one or both modules can be enrolled to the module if requested,

 Only one control panel can be enrolled to a UC or AC receiver (a

control panel repeats its PG signal every 9 minutes).

6 Control panel programming

The most convenient way to program the system is to use a PC running

OLink software. However, the system can also be programmed by keying in

the below mentioned sequences. The sequence summary table can be found

at the end of this manual.

Jablotron JA-83K Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info