631258
8
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
JA-82Y user manual - 8 - MLD51300
Programming in maintenance mode
Programming in maintenance mode requires access to be enabled by a service technician.
Otherwise, no programming is possible – any instruction sequence will be rejected by the
system and the keypad will beep four times.
The following description is intended for a system administrator, who knows the control panel
master code. All the settings can be performed via keying-in on a system keypad. An unfinished
sequence can be cancelled by pressing the # key. A sequence is only stored in control panel memory
(or executed) after the sequence has been completely entered. All the settings are only applicable if
the control panel is in maintenance mode. To enter maintenance mode, first make sure, that the
system is completely unset. Then enter the following sequence on the system keypad:
0 master code (card) The keypad will display Maintenance mode.
In maintenance mode it is possible to set transmission parameters, measure the GSM signal strength,
enable/disable remote access, set the forwarding of incoming messages, record voice messages and so on.
More details with descriptions can be found in the installation manual.
Wrongly set parameters could limit or cancel some of the
functions (alarm reporting, faults,..). When you change any
parameters, test that the system works properly.
Remote access by Internet
The system can be accessed remotely via Olink software version 2.0 and higher, which allows
complete programming by installers and also operating the system by end users. The GPRS service
(or, alternatively, SMS) is used for data transfer.
Remote access is provided by Jablotron Alarms free-of-charge (only the data transfer from the
premises is charged). The installation technician can set up remote access according to the desired
arrangement.
Accessing the communicator remotely requires its SIM card to be enabled for GPRS data
transfer. Only then can the device work properly.
You can operate the system directly using a virtual keypad by entering a programming
sequence, Olink can open a command line where the sequences can be entered the same way as if
they were entered from a system keypad. By pressing the submit button you send the instruction via
the internet network to the communicator where it will be processed. More details with descriptions
can be found in the installation manual.
The list of events can be opened in any control panel state, therefore it is not necessary to put the
control panel into a specific mode (like unsetting or switching to Maintenance Mode). The events
list records the last 255 events.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron JA-82Y GSM communicator bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron JA-82Y GSM communicator in de taal/talen: Engels als bijlage per email.

De handleiding is 0,25 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Jablotron JA-82Y GSM communicator

Jablotron JA-82Y GSM communicator Installatiehandleiding - English - 13 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info