631258
3
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
JA-82Y user manual - 3 - MLD51300
Remote control by phone
For a mobile phone, there are two ways to control the system remotely. You can either send SMS
instructions or establish an authorized connection (protected by an access code) to the system. In this
case the system is controlled by a voice menu. Press 9 to switch the phone to alarm keypad
simulation. The phone keypad can be used the same way as the system keypad. Using a fixed line
phone, you can only operate the system by dialling the communicator’s number and establishing an
authorized connection.
The below described way of remote control corresponds to the communicator’s factory default
setting. The configuration can be modified during installation. The installer should clearly explain
any changes to the default setting.
1. General rules for remote control via SMS instructions
More than one instruction can be used in a single SMS message. It has to be separated by a comma.
SMS instructions are not case-sensitive. Only standard English (ASCII) characters are accepted.
All SMS instruction words (parameters) must be separated by a space. In this document a space in an
SMS instruction will also be denoted by the underline character ‘_’.
SMS instructions can be sent from a mobile phone or from a GSM gateway.
If the % character is used, all preceding text will be ignored. The %% symbol ends processing when
used in SMS text – i.e. all the following text will be ignored. It is recommended to use this symbol at
the end of the instruction if the provider sends some additional text after your message
(advertisements etc.).
Warning: If any extra text is not separated from a valid SMS instruction text by % or %%
symbols, the SMS message will not be recognized and no instruction will be executed.
Performance of the instruction is confirmed by an SMS reply.
The default instruction texts can be customized by an installer or administrator. E.g. the command
PGX ON can be changed to SWITCH ON HEATING etc.
2. Setting (arming) by SMS xxxx_SET
The SET instruction allows you to put the system in to a set (armed) state, fully or partially. If the
system is already set, it will not change its status.
Send an SMS message containing:
xxxx_SET
where: xxxx is a valid access code (user or master)
_ is a space character
Example: Sending 4321 SET will set the system the same way as if the code 4321 had been entered
on the system keypad.
Notes:
As a factory default, setting (arming) by a SET instruction is confirmed by the system via an SMS
reply.
When the current system status does not allow system operation (e.g. when in programming mode),
you will be notified about the situation via an SMS reply.
In a split system, an xxxx_SET instruction will only have an effect on the section to which the code
xxxx belongs.
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron JA-82Y GSM communicator bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron JA-82Y GSM communicator in de taal/talen: Engels als bijlage per email.

De handleiding is 0,25 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Jablotron JA-82Y GSM communicator

Jablotron JA-82Y GSM communicator Installatiehandleiding - English - 13 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info