554977
3
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
CA-340 modular car alarm 3/4 VAV50204
Connection without a CAN-Bus converter,
controlling with RC-8x remote controls
Connection pursuant to Fig 1, setting pursuant to profile 1. The values
shown in the table in bold letters are the default ones The profile is defined by
parameter 1 setting.
A description of individual wire functions is available on page 2.
Vehicle status information is obtained via direct connection to the ignition
circuit and door, bonnet and boot switches. A thus connected car alarm can
control the central locking of the vehicle. It is possible to set an extended
locking impulse which can be used to close the windows of certain vehicle
types after arming.
Connection with a CAN-Bus converter,
controlling with RC-8x remote controls
Setting pursuant to profile 1.
Information about the vehicle status (ignition key, door, bonnet, boot) is
obtained via a CAN-Bus converter.
NOTE: The converter cannot be used to control the central locking of the
vehicle.
Direction indicator (flasher) connection
Optical signaling of arming, disarming and alarm is possible in three modes.
Direct connection to the light bulb circuits. Connection pursuant to Fig. 1.
The power supply is directed to the relay contact via a 15A fuse. The contact
output is forked using diodes and it is then connected to the left and right
direction indicator light.
Connection via a warning light switch, pursuant to Fig. 2. When this
option is selected, the INP1 input always has a feedback function (counting
the flashes) and it has to be connected to a direction indicator light power
circuit. It is therefore not possible to use this optical signaling when the alarm
is controlled with the original remote control without using a CAN-Bus
converter (this option is superior to the setting parameter 12 of profile 2, INP1
then has no function for confirmation of disarming or alarm input). The
flashing can then be controlled with the following options:
„switch“ – the relay is switched if the direction indicator lights
should flash
„button“ - the relay gives an impulse to begin and finish flashing
Profile 1 – controls the central locking
parameter
= LED on
= LED off
1
Central lock
control
Yes, ULK and LCK wires control the locks in the
vehicle
(this setting defines the function of parameters
12,13,14)
2
Rearm
Yes
No
3
Autoimo
Yes
No
4
Disarming with the
Valet button
Yes
No
5
Acoustic signaling
Yes
Partial
6
Increased volume
of signaling
Yes
No
7
Open door test
Yes
No
8
Voltage detector
Yes
No
9
Shock warning
Yes
No
10
Shock alarm
Yes
No
11
AUX output
function
EXT detector power
supply
AUX bus output
12
CL input length
0,5 sec
4 sec
13
Extended lock
impulse length
Yes ( 60 sec.)
No (length pursuant
to parameter 12 )
14
DOOR input
activation
Ground
Ground disconnection
15
INP2 input
activation
Ground
Ground disconnection
16
INP2 input
reaction
Alarm
warning
17
18
BLK output
function
Boot
control
Direct
direction
indicator
control
Direction
indicator
control
switch
Direction
indicator
control
button
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron CA-340 Nestor bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron CA-340 Nestor in de taal/talen: Engels als bijlage per email.

De handleiding is 0,26 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info