555033
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
CA-01 Car Alarm „Pulse“ 2 / 2 MDM51401
Advanced Installation, optional functions setting
The basic installation can be extended for a more advanced system.
An additional siren - can be installed into the passenger compartment.
Connect the positive pole of the siren (we recommend model SA-107) to
the green wire of the CA-01 and the negative pole to the ground. If an
alarm is triggered, the additional siren will sound for 1 minute. It can also
sound for 10 minutes, depending on the immobilization duration setting.
The additional siren can be combined together with the external
immobilization relay (limited by maximal total current output of 800mA on
the green CA-01 output) .
A Wireless Pager - can be used to transmit an alarm information to user.
We recommend pager PG-4W. The green CA-01 output (+12V when
alarm) is used to trigger paging (see pager instructions for more details
regarding its installation).
An Immobilization relay - is a suitable solution for increasing your car’s
security. Connect the additional relay (we recommend model RA-12/30A)
coil contacts between the green CA-01 output and the ground. The
Normally Closed relay contact can be used to disable the engine (the
starter control circuit, for example).
If an alarm is triggered, this relay will disable the selected circuit for 1 or 10
minutes (selectable). Immobilization is indicated by the LED being
continuously light. There is no way to switch off the immobilization before the
selected time period elapses. Pay high attention to the quality of
immobilization circuit connections. Any failure in this circuit can result in a
poor or dangerous car performance.
no. siren chirps
optional function factory default
do not use ign. key to keep
you can select
switching on and off the key
• • • • • • • • • • • • • • • •
setting mode
LED status
z
LED status
5
1
entrance delay duration
15 seconds 10 seconds
2
• •
exit delay audible indication (ticking)
enabled disabled
3
• • •
vibration detector reaction
Alarm Warning
4
• • • •
vibration detector function
enabled disabled completely
5
• • • • •
immobilization duration (+12V on green
output)
1 minute 10 minutes
6
• • • • • •
current consumption detector
enabled disabled completely
• • • • • • • • • • • • • • • •
exit of the setting mode, data is stored into the memory (EEPROM)
Hidden Button Arming - if you do not want to use the ignition key for
arming, install a push button switch in a hidden location. Connect the blue
CA-01 input wire to this switch so that there is +12V on the input if the
button is pressed. The arming logic is the same (press twice for arming,
once for disarming).
Note: If you use the hidden button for arming, disable only the starter with
the immobilization relay. This will prevent an accidental immobilization
when driving.
A Warning Function - the vibration detector function can be switched
from the alarm trigger to a warning trigger (see setting mode). If the
warning function is selected, any detected vibration will result only in a
short siren chirp when is CA-01 armed. The digital filter will not filter out
independent vibrations.
The vibration detector can also be completely disabled in the setting
mode.
Setting mode
Optional functions can be modified in this mode. Read the following
descriptions, then enter the setting mode:
1) disconnect the CA-01 power (red wire)
2) turn on the ignition key
3) wait 1 minute then reconnect the power
4) switch the ignition key off and then switch it on and off five times
5) the siren will make 16 short chirps indicating that the setting mode
was entered
The car alarm will automatically offer one optional function every
3 seconds (see the following table). The number of the function (row
number in the table) is indicated by number of the siren chirps.
If you want to select the offered function, switch on and off the ignition
key (LED goes off). If you do not want to select the offered function, wait
until the CA-01 will offer the function you want to modify.
After all functions are offered, the CA-01 will close the setting mode
automatically (confirmed by 16 siren chirps. All data is stored to the
memory). If you do not select any offered function in the setting mode, the
car alarm will return to the factory default settings.
Note: If you switch the ignition key on for longer than 10 seconds in any
offered function level, the setting mode will be terminated and no changes
will be stored to the memory.
Vibration detector testing
If you want to test the built-in vibration detector sensitivity, perform steps
no. 1, 2 and 3 of the setting mode entering (see above). After power
reconnecting leave the ignition key on and you can test vibration detector
now (triggering is indicated by a LED flash and a siren chirp). Switch off
the ignition key for more then 10 seconds to exit testing mode.
Note: Although this product does not contain any harmful materials we
suggest you to return the product to the dealer or directly to the producer
after usage.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron CA-01 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron CA-01 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,18 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info