557984
2
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
year intervals as part of the normal time switch
maintenance observing battery polarity markings when
installing. No other maintenance is required.
8.
Place the slide switches in the AUTO and RUN position.
9. Reapply power to the time switch.
10. Press the recessed reset switch for at least two
seconds. The display will show 12:00 A.M. and MO.
Note that the days of the week are identified with the
first two letters of the day (MO for Monday).
The timer is now ready for programming. Refer to the
examples which follow and enter the scheduled events
(set points) required. Assign each of the 12 set
points (EVENTS) entered to whichever day or groups
of days of the week you wish an ON or OFF
operation to occur.
Set Point = Event = ON = OFF
PROGRAMMING STEPS:
SET CURRENT DAY AND TIME
Slide switch to TIME SET. Push DAY until current day
shows, then push HOUR until current hour AM or PM
shows. Now push MINUTE until current minute
shows. Clock is now set. Follow same procedure after
replacing battery or changing time (such as
for daylight saving time).
SET YOUR PROGRAM
Slide switch to PROG. Display will look like this: (-:- -)
Press DAY until desired program period shows (see
choices in “PROGRAM PERIOD OPTIONS” section
above).
Press HOUR until desired “ON 1” hour shows (that
is, the first time each day of the program period that
you want the load to turn ON).
Press MINUTE until desired minute shows.
Press EVENT to program time for ON 1 (and to
advance to programming for OFF 1).
Press DAY again until all seven days of the week
show (or until another desired program period
option shows; see “PROGRAM PERIOD
OPTIONS”).
Press HOUR again until desired “OFF 1” hour shows
(that is, the first time each day of the program
period that you want the devices to turn OFF).
Press MINUTE until desired minute shows.
Press EVENT to set time for OFF 1. You may now
begin setting ON 2, a second ON time, for the same
program period, OR press DAY to change to a
different program period.
Repeat above procedure until all desired ON/OFF
programs are set.
PLEASE NOTE: Before you program your timer, or when you
remove the battery, or when you use the RESET, pressing
EVENT will display the bar symbol -:-- ON 1. Repeated press-
ing of EVENT will display all the way through the final bar sym-
bol -:-- OFF 6. Once you program your timer, however, each
actual time setting you make will replace the bar symbol. While
programming, each time you press EVENT you will advance to
the next EVENT.
PROGRAM PERIOD OPTIONS:
Your timer gives you up to 6 different ON and 6 different OFF
settings per program period. You can use all 6 settings per peri-
od, or as few as you like. A program period covers one of these:
ALL 7 DAYS OF THE WEEK combined into one -
display shows: MO TU WE TH FR SA SU.
MONDAY THRU FRIDAY combined into one -
display shows: MO TU WE TH FR.
SATURDAY AND SUNDAY combined into one -
display shows: SA SU
EACH INDIVIDUAL DAY OF THE WEEK -
display shows only that day.
BLANKDAY EXPLANATION - “BLANKDAY”
follows Sunday after last push of DAY button (when
the lower slide switch is set at PROGRAM). The
purpose of the BLANKDAY is to disable a program
setting on a day.
Program periods with days “combined into one” help you
make settings for those multiple days quickly and conve-
niently while using only one ON/OFF pair. When you set
such a program period, all settings will be identical for
every day of that period.
PERSONAL
PROGRAM EXAMPLES
EVENTS
DAY CHECKS ON TIMES OFF TIMES DISPLAYED DAYS & TIMES DISPLAYED
EXAMPLE 1
MO TU WE TH FR SA SU 5:00 PM 10:00 PM ON 1 MO TU WE TH FR SA SU 5:00 PM
OFF 1
EXAMPLE 2
MO TU WE TH FR
6:00 PM 10:00 PM ON 1 MO TU WE TH FR 6:00 PM
OFF 1 MO TU WE TH FR
10:00 PM
SA SU 4:00 PM 8:00 PM ON 2 SA SU 4:00 PM
OFF 2 SA SU 8:00 PM
EXAMPLE 3
MO TU WE TH FR 6:00 AM 9:30 AM ON 1 MO TU WE TH FR 6:00 AM
OFF 1 MO TU WE TH FR 9:30 AM
MO TU WE TH FR 5:30 PM 11:15 PM ON 2 MO TU WE TH FR 5:30 PM
OFF 2 MO TU WE TH FR 11:15 PM
SA SU 3:00 PM 10:00 PM ON 3 SA SU 3:00 PM
OFF 3
SA SU 10:00 PM
EXAMPLE 4
MO TU WE TH 8:00 PM 11:30 PM ON 1 MO TU WE TH 8:00 PM
OFF 1 MO TU WE TH 11:30 PM
FR SA 5:00 PM 2:20 PM ON 2 SU 7:00 PM
(DAY AFTER) OFF 2 SU 10:30 PM
SU 7:00 PM 10:30 PM ON 3 FR 5:00 PM
OFF 3
MO 11:30 PM
ON 4
SA 5:00 PM
OFF 4
TU 11:30 PM
ON 5 “BLANKDAY” -:- -
OFF 5 WE 11:30 PM
ON 6 “BLANKDAY” -:- -
OFF 6 TH 11:30 PM
NOTE: “-:- -” follows Sunday after last push of DAY button
(when the slide switch is set at PROG). The purpose of the
-:- - is to cancel a program setting on that day.
REVIEW YOUR PROGRAM
Slide switch to PROG. Press EVENT button to advance
display to each ON or OFF setting. Check days and times
displayed. To make a change, follow instructions under
“SET YOUR PROGRAM”. To delete a displayed set point,
press DAY button until “-:- -” is displayed.
GENERAL FEATURES AND HINTS FOR TROUBLE-
FREE USE
BUTTON: When you press a button, there is an advance
of one time unit; holding a button down advances contin-
uously until released.
MAINTENANCE: With the exception of battery replace-
ment at 2-3 year intervals, your Intermatic timer is
maintenance-free.
AFTER THE INSTALLATION IS COMPLETED, THE
LOCKABLE HASP SHOULD BE MOVED TO THE UP
POSITION TO ENGAGE THE COVER WHEN IT IS
CLOSED.
FULL ONE YEAR WARRANTY
If within one (1) year from the date of purchase, this product fails
due to a defect in material or workmanship, Intermatic
Incorporated will repair or replace it free of charge. The warranty
does not apply to (a) damage caused by accident, abuse, mis
-
handling or dropping: (b) units which have been subject to unau-
thorized repair, opened, taken apart; (c) units not used in accor-
dance with directions; (d) damages exceeding the cost of the
product. Some states do not allow a limitation of damages, so the
foregoing limitation may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights which
vary from state to state.
This warranty service is available by either (a) returning the prod-
uct to the dealer from whom the unit was purchased, or (b) mail
-
ing postage prepaid to the authorized service station listed below.
Please be sure to wrap the product securely when mailing to
avoid damage.
This warranty is made by: Intermatic Incorporated,
Intermatic Plaza, Spring Grove, Illinois 60081-9698.
AUTHORIZED SERVICE STATION
INTERMATIC INCORPORATED
4720 West Montrose Avenue
Chicago, Illinois 60641
INTERMA
TIC INCORPORA
TED
SPRING GROVE, ILLINOIS 60081-9698
158ET8805 PRINTED IN U.S.A.
TIMER
POWER
LOAD
NEUTRAL
NEUTRAL
1
234
Fig. 4
Fig. 5
TIMER
POWER
1
23
4
56
LINE 1
LINE
LINE
LINE 2
LINE 1
LINE 2
LOAD
120
240
EH10
EH40
- 2 -
See
Pg. 7
See
Pg. 7
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Intermatic EH10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Intermatic EH10 in de taal/talen: Engels, Frans, Spaans als bijlage per email.

De handleiding is 0,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info