627060
25
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
25
CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED
9.4 Thread cUTTinG
Connect the thread cutting axis by moving lever for selection of feed/thread range to the right and the lever
for thread cutting downward. The transmission (longitudinal travel) for thread cutting is obtained. The direction for
thread cutting is selected with the switch on the headstock. The desired thread cutting is selected by means of the
handles on the gear box.
9.5 Thread cUTTinG dial
The thread cutting dial is located on the right side of the apron and is used for thread cutting with the lead screw. For
an even thread, close the half nut at the desired line of the dial, for an odd number on a numbered line. The thread
cutting dial should stand on the same spot at every cut. To avoid wear, it is recommended to disconnect the pin of
the thread cutting dial from the lead screw if not used.
9.6 cross slide and Tool holder
A tool holder is mounted on the tool post. The upper part contains a 0-45
0
left/right scale. The vernier scale on the
hand wheels correspond with the type of machine (Metric or Whitworth).
9.7 TailsTock
The tailstock is used to produce small parts. It can be adjusted transverse by using the set screws, that are mounted
on both sides of the tailstock. First, make sure that the locking lever of the tailstock is loosened. Loosen the screw at
the back. First, loosen one set screw, than the other, until the desired position is obtained. Tighten both screw and
the locking lever. The tailstock pinole can be tightened with the handle.
10. adjUsTinG
When the lathe is installed and ready for use, it is recommended to check the machine alignments before
commencing work. Alignment and levelling should be checked regularly to ensure accuracy.
The V-belts can be reached after removing the back splashguard, the cover and the V-belt guard cover. The motor is
mounted at the back of the bed on a plate that can be adjusted vertically. The plate is clamped with two stay bolts
and nuts. The belt tension is adjusted by turning the two hex nuts at the top of the plate outwards. Check the pulley
settings by putting a builder’s level over the pulleys. Make sure that the pulleys stay in line.
Use the hex screw on the bottom side of the tailstock between the guides to adjust the locking lever of the tailstock.
Adjust the transverse guiding by adjusting the tapered key with the slotted bolt at the front of the cross slide. First,
loosen the bolt at the back of the cross slide and tighten the bolt on the front by turning clockwise. Tighten the bolt
at the back after making the adjustments.
Follow this procedure to adjust the guide of the tool slide, only now use the slotted bolt on the front of the tool post.
Wear of the cross bolt can be compensated:
Remove the protection plate at the back of the cross slide. Turn the hand wheel of the cross slide clockwise until the
end of the cross spindle is reached. Turn the bolt at the end clockwise, as far as needed. Do not over tighten the bolt:
a rotation of 45° matches a play of 0.125 (.005”).
The spindle bearing has already been adjusted. The right setting is 0,0050 mm (0,0002”), the spindle can still be
moved by hand.
Technical changes and developments can lead to small deflection in the specifications and descriptions above. This
also applies for the part lists and drawings.
25

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Huvema-HU-1010-B-4-SINO

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Huvema HU 1010 B-4 SINO bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Huvema HU 1010 B-4 SINO in de taal/talen: Engels als bijlage per email.

De handleiding is 7,37 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Huvema HU 1010 B-4 SINO

Huvema HU 1010 B-4 SINO Gebruiksaanwijzing - Nederlands - 48 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info