32351
6
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
69-1085
6
CT2700 AN ELECTRONIC ROUND
PROGRAMMABLE THERMOSTAT
Hold Function
To hold the thermostat at one temperature indefinitely,
program both WAKE and SLEEP to the same
temperature.
9 SET FAN AND SYSTEM SWITCHES
Manually control fan and system settings using the
switches located at the top of the thermostat case. See
Fig. 11 for switch locations.
10 CHECK OPERATION AFTER
INSTALLATION/PROGRAMMING
Heating System
Slide the System switch to HEAT and the Fan switch
to AUTO.
Press and hold the key to raise the temperature
several degrees above the room temperature to
start the heating equipment. When using the
thermostat with the fuel switch set to the E position
for electric heat, the fan starts immediately.
Press the key to lower the temperature setting
below the room temperature. The heating equipment
should stop.
Cooling System
CAUTION
Operating at too low of an outdoor temperature
may cause compressor damage
Damage to compressor possible.
Do not operate cooling system if outdoor tempera-
ture is below 50°F (10°C). Refer to manufacturer
recommendations.
IMPORTANT
Temporary protection delay protects compressor;
the thermostat allows the compressor to remain
off for five minutes before restarting.
Slide the System switch to COOL and the Fan
switch to AUTO.
Press the key to lower the temperature setting
several degrees below the room temperature to start
the cooling equipment.
Press the key to raise the temperature setting
above the room temperature. The cooling equipment
should shut down.
Fan
Slide the System switch to OFF and the Fan switch
to ON. The fan should run continuously.
CUSTOMIZE YOUR THERMOSTAT
The following instructions provide the information neces-
sary to change the heating cycle rate to match your
heating equipment; choose Fahrenheit (°F) or Celsius
(°C); and 12- or 24-hour clock.
To exit at any time, press until End is displayed.
1. Enter Installer Setup
a. Slide System switch to OFF position.
b. Use the or
keys to
set
the temperature
setpoint to 52°F
(11°C).
Set
M12523
TEMPERATURE DISPLAY
INCREASE
SETTING
DECREASE
SETTING
FAN SWITCHSYSTEM SWITCH
C
O
O
L
O
F
F
H
E
A
T
F
A
N
O
N
A
U
T
O
PM
Fig. 11. CT2700 time/temperature display and
system/fan switches.
Fan Switch
The FAN switch settings are:
ON: The fan runs continuously. Use for improved air
circulation.
AUTO: Normal setting for most homes. In cooling,
the fan starts and stops with the cooling equip-
ment. In heating, the fan is controlled directly by
the heating equipment and starts a few minutes
after the heating equipment turns on (on most
systems). When the thermostat fuel switch is set
to the E position for electric heat, the fan starts
and stops with the heating equipment.
Slide the switch on the thermostat to the desired fan
setting.
System Switch
The System switch settings control thermostat
operation as follows:
COOL: The thermostat controls the cooling system.
OFF: Both heating and cooling are off.
HEAT: The thermostat controls the heating system.
Slide the System switch on the thermostat to the
desired system setting.
SET
AM
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Honeywell CT2700 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Honeywell CT2700 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,49 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info