110241
8
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
7
4. Plunge cutting
With this tool, you can perform plunge cutting on
plywood panels and thin board materials. You can
carry out pocket cutting quite easily with the saw blade
installed in reverse as illustrated in Fig. 24, Fig. 26,
and Fig. 28. Use the saw blade that is as short and
thick as possible. We recommend for this purpose that
you use BI-METAL Blade No. 132 mentioned in Table
2. Be sure to use caution during the cutting operation
and observe the following procedures.
(1) Press the lower part (or the upper part) of the base
against the material. Pull the switch trigger while
keeping the tip of the saw blade apart from the
material. (Fig. 23, Fig. 24)
Fig. 23
Fig. 24
(2) Raise the handle slowly and cut in with the saw blade
little by little. (Fig. 25, Fig. 26)
Fig. 25
Fig. 26
(3) Hold the body firmly until the saw blade completely
cuts into the material. (Fig. 27, Fig. 28)
Fig. 27
Fig. 28
CAUTION
Avoid plunge cutting for metallic materials. This can
easily damage the blade.
Never pull the switch trigger while the tip of the saw
blade tip is pressed against the material. If you do so,
the blade can easily be damaged when it collides with
the material.
Make absolutely sure that you cut slowly while holding
the body firmly. If you apply any unreasonable force
to the saw blade during the cutting operation, the
blade can easily be damaged.
SELECTION OF BLADES
To ensure maximum operating efficiency and results, it is
very important to select the appropriate blade best suited to
the type and thickness of the material to be cut.
NOTE:
Dimensions of the workpiece mentioned in the table
represent the dimensions when the mounting position
of the base is set nearest to the body of the
reciprocating saw. Caution must be exercised since
dimensions of the workpiece will become smaller if
the base is mounted far away from the body of the
reciprocating saw.
1. Selection of HCS blades
The blade number of HCS blades in Table 1 is
engraved in the vicinity of the mounting position of
each blade. Select appropriate blades by referring to
Tables 1 and 4 below.
01Eng_CR13VBY_Eng.p65 7/19/12, 4:34 PM7
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi CR 13 VBY bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi CR 13 VBY in de taal/talen: Engels als bijlage per email.

De handleiding is 1,05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Hitachi CR 13 VBY

Hitachi CR 13 VBY Gebruiksaanwijzing - Nederlands, Deutsch, English - 60 pagina's

Hitachi CR 13 VBY Gebruiksaanwijzing - English - 60 pagina's

Hitachi CR 13 VBY Gebruiksaanwijzing - Français, Italiano, Português, Espanõl - 60 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info