110241
5
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
4
MAINTENANCE AND INSPECTION OF SAW BLADE
MOUNT
(1) After use, blow away sawdust, earth, sand, moisture,
etc., with air or brush them away with a brush, etc., to
ensure that the blade mount can function smoothly.
(2) As shown in Fig. 8, carry out lubrication around the
blade holder on a periodic basis by use of cutting fluid,
etc.
Fig. 8
NOTE:
Continued use of the tool without cleaning and
lubricating the area where the saw blade is installed
can result in some slack movement of the lever due
to accumulated sawdust and chips. Under the
circumstances, pull a rubber cap provided on the lever
in the direction of an arrow mark as shown in Fig. 9
and remove the rubber cap from the lever. Then, clean
up the inside of the blade holder with air and the like
and carry out sufficient lubrication. The rubber cap
can be fitted on if it is pressed firmly onto the lever.
At this time, make certain that there exists no
clearance between the blade holder and the rubber
cap, and furthermore ensure that the saw-blade-
installed area can function smoothly.
Fig. 9
CAUTION:
Do not use any saw blade with a worn-out blade hole.
Otherwise, the saw blade can come off, resulting in
personal injury. (Fig. 10)
Fig. 10
7. Adjusting the base
This unit employs a mechanism that can adjust the
base mounting position in three stages without the
use of a wrench or other tools.
Lever
Blade holder
Machine oil
Lever
Rubber cap
Blade
Blade hole
(1) Press a pushbutton. When you do this, a base lever
will jump out to prepare the base for adjustment.
(Fig. 11)
Fig. 11
2) Push up the base tip and jog the base back and forth.
(Fig. 12)
Fig. 12
(3) You can adjust the base position in three stages. Move
the base at an interval of about 15 mm, find the
position where the base hooks, and press in the base
lever with your fingers. The base is secured when you
hear the clicking sound. (Fig. 13)
Fig. 13
8. Adjusting the blade reciprocating speed
This unit has a built-in electronic control circuit that
makes it possible to adjust the variable speed of the
saw blade either both by pulling a switching trigger
or turning a dial. (Fig. 14)
Push button
Base lever
Base
Base lever
01Eng_CR13VBY_Eng.p65 7/19/12, 4:34 PM4
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi CR 13 VBY bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi CR 13 VBY in de taal/talen: Engels als bijlage per email.

De handleiding is 1,05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Hitachi CR 13 VBY

Hitachi CR 13 VBY Gebruiksaanwijzing - Nederlands, Deutsch, English - 60 pagina's

Hitachi CR 13 VBY Gebruiksaanwijzing - English - 60 pagina's

Hitachi CR 13 VBY Gebruiksaanwijzing - Français, Italiano, Português, Espanõl - 60 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info