628793
9
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
Max. carrying
capacity (tonnes):
8 12 15 20
Min. height (mm): 200 210 225 235
Lift height (mm) : 125 125 140 145
Adjustment height
(mm)*:
80 80 80 60
Max. final height
(mm):
405 415 445 440
Weight (kg): 5,5 7,2 9 11
Ordering No.: 84115 84117 84118 84120
* max. setting screw lift
Lifting (Fig. 3)
On a flat surface under the vehicle with sufficient capacity.
Secure the vehicle against rolling away.
Find the designated anchoring point on the vehicle.
Close the valve (A) pic. 2, pos. 9.
Pump or – to be more specific – lift up (C)
Secure the vehicle with supports under axles!
Lowering (Fig. 3)
Remove the supports under axles.
Slowly open the valve (A).
Operation (Fig. 3)
Lifting
1. The opened drain valve (2) will be closed by turning the
lifting lever small end (1) to the right.
2. Put the vehicle lifting jack under the vehicle to be lifted,
specifically under the determined clamp (read the vehicle
operating manual) . If necessary, remove the extension
screw (3) turning it to the left from the hub so that it
touches the vehicle. The precise attachment point may be
determined in that way.
3. Put the lifting laver (4) in the pump (5) and lift the vehicle
to the required height pumping.
Senken
Lower the vehicle slowly. Open the drain valve
slowly!
Open the drain valve by pushing the lifting lever small end
into the valve and turning the lever slowly to the left.
Open the drain valve by 1 turn as a maximum!
If the vehicle is lowered at full, pull out the jack. If the
extension screw is screwed out, screw it in before removing it
turning to the right again as far as to the stop.
Operator Safety Instructions
Do not use the machine until you have read the
instruction manual carefully.
Observe any safety instructions included in the manual.
Be responsible to the others.
Inspections and Maintenance
Hydraulic Oil Replenishment (Fig. 4):
1. Put the vehicle lifting jack vertically.
2. Check if the jack is lowered completely. If necessary
lower it to the stop.
3. Remove the oil filler plug (filling hole) from the body.
4. Pour premium quality hydraulic oil in the cylinder up to
the filler hole lower edge. De-aerate the cylinder
proceeding according to the description in part 4 (De-
aeration).
5. Put the filler plug back in the body.
Lubrication:
Lubricate the moving parts and the enlargement screw
threading regularly to provide the vehicle lifting jack safe
functioning.
De-aeration
Air bubbles may enter the vehicle lifting jack hydraulic system
with time and affect its functioning.
1. Open the drain valve and remove the filler plug.
2. Push the pump down several times to get the air out of
the system.
3. Close the drain valve and replace the filler plug.
4. Now, the vehicle lifting function should be easy and
appropriate. If it is not, repeat the procedure once again.
Corrosion Prevention
If the lifting jack is out of use, you will prevent the corrosion of
the unit by full lowering of the lifting piston, screwing the
enlargement screw and lowering the pump.
Avoid any contact of moving parts with dirt. If the vehicle
lifting jack still gets dirty, clean it carefully and grease the
moving parts.
Inspections and Maintenance Safety Instructions
The machine will serve as a sufficient aid only if maintained
and cared for appropriately. Insufficient maintenance and care
may result in accidents and injuries.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gude 3T 18017 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gude 3T 18017 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 0,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info