590653
6
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
6 GMC-I Messtechnik GmbH
If the symbol is included in the description of the surge pro-
tection device, the manufacturer’s instructions must be observed
for the respective device type.
The actual measurement is performed as follows:
Select measurement of surge protection devices with the
R
ISO/USPD key, and select the desired sub-function with the
FUNC key (see also description above). Example:
Figure 3.11: Surge Protection Device Measurement Menu,
DC Function
Connect the test probes to the surge protection device in ac-
cordance with the manufacturer’s instructions.
Figure 3.12: Connection Example
Note
If a voltage of greater than about 10 V is present at the measured
surge protection device, its value is displayed and the START key is
disabled (see section 3.3.1 on page 4). Eliminate the source of
interference voltage before restarting the measurement.
Trigger measurement by pressing the START key. Release the
START key as soon as measurement is started. Rising current
at the surge protection device is displayed by means of a bar
graph. At the same time, the measuring voltage value appears
at the display in the U
IN field. Measurement is ended automat-
ically.
Read voltage measured at the milliampere point.
Note
The device under test may not be disconnected from the
test instrument as long as the “!” warning symbol is lit up.
After insulation measurement has been completed, any remaining
residual voltage is displayed as UIN, which may result from cable
capacitance. Contact to the device under test must be main-
tained for as long as the capacitive DUT is being discharged via
the test instrument’s internal resistor. The falling voltage value can
be observed directly at the UIN display. Do not disconnect the
DUT until voltage U
IN is less than 25 V!
Comments
Before measuring surge protection devices, disconnect them
from the installation.
It’s advisable to study the circuit before performing measure-
ment. Surge protection devices are currently equipped with
integrated interference suppression filters and the like, which
may influence measurement results.
3.4 Further Device Functions
Select Language, Query Firmware Version
Before selecting a language or querying the firmware version, dis-
connect both test probes from the device under test / measuring
circuit and switch the test instrument off.
Press and hold the R
ISO/USPD key while switching the test in-
strument on.
The firmware version and other service information appears at the
display, as well as the language selection menu.
Select the desired language with the corresponding key
(EN = English, CZ = Czech).
Figure 3.15: Language Selection Menu
The instrument is switched back to normal operation after a lan-
guage has been selected.
Measuring Point Illumination with White LED
The LED can be switched on and off by briefly pressing the START
key.
No voltage may be applied to the test probes.
!
Figure 3.13: Sample Results
for the USPD
Measurement
(discharging is
active: residual
voltage = 144 V)
Figure 3.14: Further Sample
Results for the
U
SPD Measure-
ment (DUT is fully
discharged: resid-
ual voltage = 0 V)
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gossen Metrawatt METRALINE ISO-CHECK bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gossen Metrawatt METRALINE ISO-CHECK in de taal/talen: Engels als bijlage per email.

De handleiding is 0,39 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Gossen Metrawatt METRALINE ISO-CHECK

Gossen Metrawatt METRALINE ISO-CHECK Gebruiksaanwijzing - Nederlands - 8 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info