534703
254
Verklein
Vergroot
Pagina terug
1/256
Pagina verder
X400 3D-Printer Manual
Seite 254 /
Revision 367
Stand 08.01.201414:30
Kapitel 7. Troubleshooting›Too little material is printed
© German RepRap GmbH 254 /
Once the function of the end stops has been verified, the cabling has to be checked. Also, the end stops have to
be plugged on the "min" contacts of the Ramps, as those limit the downward movements. The upper restriction
of the movement is preset via the firmware.
7.6. Too little material is printed
At first, it has to be checked whether there is a mechanical problem. If the extruder motor rotates but no material
is coming out of the hot end, the hot end might be blocked. Also, the filament screw might be at fault, so that
it is not conveying material to the hot end. Once the mechanics are checked, the flow rate has to be increased.
In Slic3r, this is adjusted via the item "Extrusion multiplier".
7.7. The printer breaks off printing and stops responding
If the printer breaks off the printing process there are three possible reasons. First, it should be checked whether
the power supply was interrupted. The problem may also be caused by an interruption of the data connection
to the computer, the crashing of a program or a disconnected USB cable.
If neither is the case, it is possible that the Pololu shut down due to overheating. This can easily be validated
by touching the Pololu heat sink. Thirdly, the Ramps fan might not sufficiently cool the Pololus or the
potentiometer may be set too high.
If the potentiometer can not be decreased due to possible step losses, it has to be examined whether the motor
works against an increased resistance, e.g. some misalignment of the rods after moving or bumping the device.
This resistance would have to be eliminated and the potentiometer readjusted afterwards.
7.8. Glue on of the PET-foil bubble-free
To attach the PET-foil bubble-free on the printing bed we advise the following:
moiste the printing bed with water oder window cleaner
apply the PET-Foil on the dampish surface (remove carrier foil from the PET-foil)
displace and absorb the excess fluid (with such as squeegee or check card)
heat up the heated bed (if available) at 30°C until all the fluid is not longer present.
254

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw German RepRap X400 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van German RepRap X400 in de taal/talen: Engels als bijlage per email.

De handleiding is 43,61 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info