534703
253
Verklein
Vergroot
Pagina terug
1/256
Pagina verder
X400 3D-Printer Manual
Seite 253 /
Revision 367
Stand 08.01.201414:30
Kapitel 7. Troubleshooting›The printer cannot be connected with the repeating host
© German RepRap GmbH 253 /
Kapitel 7. Troubleshooting
Service
If you have questions regarding the commissioning or operation or in case of a problem, please
contact your stockist or the support of the company German RepRap GmbH via their website
(https://www.germanreprap.com).
7.1. The printer cannot be connected with the repeating host
In case the connection with the printer via Repetier-Host fails, it has to be checked whether a different program
uses the port "COMx "for the communication with the printer., e.g. the Arduino software. Quit the other
software if necessary. After that, or if no other program uses the port "COMx", the reset button has to be pressed
to restart the printer. Unplugging and replugging the USB cable has the same effect. Now the printer should
be available.
7.2. No commands are transmitted to the printer
If no commands like movements of the axes or heating of the hot end are transmitted to the printer via the
Repetier-Host, the electrical supply has to be checked. Make sure the power supply is switched on and connected
to the RAMPS. In case the problem persists and is not related to the power supply, updating the firmware may
solve the issue.
7.3. The motors cannot be controlled
Problems with the controlling of the motors can have different reasons. At first it should be verified that the
power supply of the RAMPS electronics is switched on and correctly wired. In case the electrical supply is not
the problem, the wiring of the motors may be at fault. If the difficulty with the motors still persists, check
whether the firmware was correctly transferred onto the Arduino board. This can simply be validated by heating
up the hot end.
7.4. The Y-axis cannot be moved and only produces loud noises
If both motors are clicking but the Y-axis is not moving, the wiring of the Y-axis might be at fault. As shown in
the "Circuit diagram[S.193]", the Y-axis motors have to be wired with opposite polarity, meaning the motors
are supposed to move in different directions.
7.5. The motors rotate in one direction only
If the motors only rotate in one direction, the problem lies with the end stops. In that case, the functionality
of the end stops has to be checked. The LED has to flash when switched on and the light barrier is not broken.
The LED should stop flashing when the light barrier is broken, e.g. with a screwdriver.
253

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw German RepRap X400 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van German RepRap X400 in de taal/talen: Engels als bijlage per email.

De handleiding is 43,61 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info