714637
61
Verklein
Vergroot
Pagina terug
1/65
Pagina verder
EN EN
120 121
Problem Reason Easy solution
You attempted to com-
bine the parts of different
tool sets.
Do not mix up the parts
of different tool sets. Only
use matching parts of
one single tool set (see:
‘Knowing Your New Stand
Mixer’). For making pasta
or minced meat only use
one single disc.
Schalten Sie den Motor sofort aus (Regler drücken). Zie-
hen Sie den Netzstecker aus der Steckdose. Vergewissern
Sie sich, dass Sie den Fleischwolf richtig und vollständig
zusammengesetzt haben (siehe: ‚Mit dem Fleischwolf
arbeiten‘). Fixieren Sie den Stift in der Mitte der Schne-
cke mit dem entsprechenden Adapter oder der Scheibe
des verwendeten Werkzeugsatzes.
The screw ring got loose. Immediately switch off the motor (press the control dial) and
unplug the machine. Ensure that the screw ring is turned on
sufficiently firm. The used tool set may not wobble within the
mincer housing (see: ‘Using the Mincer’).
Hart parts of the food got
caught between the worm
shaft, cross blade, and
mincer housing.
Immediately switch off the motor (press the control dial)
and unplug the machine. Remove the mincer from the
mixing arm and disassemble the mincer. Remove any
obstacles from the interior of the mincer (see: ‘Using the
Mincer / Removing Obstacles’).
Pasta dough comes out
only in short threads.
The pasta disc is not in
the correct orientation.
Switch off the machine (press the control dial) and
unplug. Check, if the pin of the worm shaft is inserted
into the well in the centre of the pasta disc. Check, if the
spigots at the rim of the pasta disc are engaged in the
notches at the rim of the mincer housing.
You are using some insuf-
ficient tools.
Ensure to assemble the mincer completely and correctly
according to the appropriate instructions (see: ‘Using the
Mincer / Making Noodles and Pasta’). Do not use any
parts of any other tool set. Only the pasta tools are sui-
ted for forming pasta.
You did not insert the
pasta dough evenly into
the feed chute.
Knead the pasta dough to a compact roll of 2cm in dia-
meter. Try to insert the dough roll in a steady pace into
the feed chute. If required, spread some flour onto the
roll, before processing. If required, slow down the speed
setting a little.
The pasta dough sticks to
the inner walls of the feed
chute.
Knead the pasta dough to a compact roll of 2cm in diameter.
Spread some flour onto the roll, before processing and/or
stop and unplug the machine and rub the inner walls of the
feed chute with some cooking oil for making the dough slide
down somewhat easier. Try again.
Problem Reason Easy solution
There are a lot of bubbles
in the pasta dough and/or
the pasta dough is too dry
and crumbly or too runny.
Pasta dough must be as heavy and glutinous as bread
dough. Knead the dough to a roll as compact as possible.
Insert the dough roll in a steady pace. This may avoid
making air bubbles within the mincer housing.
When processing dough
for pasta / noodles or
cookies, the dough sticks
stubbornly to the inner
walls of the feed chute.
The dough is too sticky. Shortly press the control dial for switching to the pause
function. Then spread some flour onto the dough roll and
try again. If this is not sufficient, switch off the machine
and unplug. Rub the inner walls of the feed chute with
some cooking oil. Then try again.
Your food comes out at
the rim of the screw ring.
The mincer is not assem-
bled correctly.
Ensure to assemble the mincer completely and correctly
according to the instructions given in this booklet (see: ‘Using
the Mincer’). Do not attempt to mix up the tools of different
tool sets (see: ‘Knowing Your New Stand Mixer’). Ensure to
assemble the parts of the tool set in correct orientation.
The screw ring got loose. Turn on the screw ring somewhat tighter but do not use
violence. The worm shaft must be able to move within
the mincer housing.
Your food is too runny
and/or too wet.
Do not process runny batters or juicy fruit and vegetables
(e.g. cucumbers) with the mincer.
The motor stops unex-
pectedly and/or the motor
does not start.
The motor ran continuo-
usly for a too long time
period. The overheat pro-
tection is active.
Immediately unplug the machine. Wait for approx. 20
minutes. Do not let the motor run continuously for more
than 10 minutes. In time, make breaks of approx. 5
minutes.
The screw ring is fixed too
tightly. The overload pro-
tection is active.
Immediately unplug the machine. Wait for approx. 20
minutes. Remove the mincer from the mixing arm. Do not
turn on the screw ring with violence. If required, loosen the
screw ring a little, before starting operation again.
The worm shaft or cross
blade is blocked by some
hard or fibrous parts of
your food. The overload
protection is active.
Immediately unplug the machine. Wait for approx. 20
minutes. Do not fill any too hard pieces of food into the
mincer. The machine is not suited for grinding nuts or
other food with similar consistency. Cut your ingredients
to pieces of approx. 2 x 2 x 6 cm. Do not press too hard
onto the pusher. Remove the mincer from the mixing arm
and remove the obstacle, before starting operation again
(see: ‘Using the Mincer / Removing Obstacles’).
61

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gastroback 40977 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gastroback 40977 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 1,22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info