747946
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Applicable systems: Futaba S-FHSS 2.4GHz system and TM-FH RF Module
R2001SB
S-FHSS 2.4GHz System
S.BUS Port and 1 Channel (CH3) for Conventional System
Receiver
56%6SHFLÀFDWLRQV
S-FHSS 2.4GHz system/S.BUS port and 1 channel for conventional system receiver
• Dual antenna diversity
• Size: 0.83 x 1.65 x 0.21 in. (21.1 x 41.8 x 5.3 mm)
• Weight: 0.15 oz. (4.2g)
Thank you for purchasing a Futaba R2001SB S-FHSS 2.4GHz compatible receiver.
The R2001SB has an S.BUS system output port and a conventional system channel output. It can also be used with
conventional system servos, etc. in addition to S.BUS system compatible servos and gyros.
LED Indication
Green Red Status
Off Solid No signal reception
Solid Off Receiving signals
Blink Off Receiving signals but ID is unmatched
Alternate blink Unrecoverable error (Memory, etc.)
Antenna installation precaution
Do not cut or bundle the receiver antenna wire.
Do not bend the coaxial cable. It causes damage.
The antenna should not be pulled.
Keep the antenna as far away from the motor, ESC
and other noise sources as you possibly can.
Do not touch the antenna to metal, carbon, or other
conductive material.
Be sure that the two antennas are placed at 90
degrees to each other.
The R2001SB has two antennas. In order to maximize signal
reception and promote safe modeling Futaba has adopted a diversity
antenna system. This allows the receiver to obtain RF signals on
both antennas and fly problem-free.
Antenna installation for carbon fuse
WARNING
The antenna portion of 30mm tip must be fully
exposed.
Please make sure that the exposed portion won't slide back in the
fuse due to wind pressure or other force during the flight session.
Usage precaution
Futaba S-FHSS system does not work with current Futaba FASST/
FASSTest/T-FHSS system. Futaba FASST/FASSTest/T-FHSS sys
-
tem and S-FHSS system are not compatible to each other.
WARNING
Wrap the receiver with something soft, such as foam
rubber, to avoid vibration. Moreover, the receiver must
not get wet.
Do not short-circuit the connectors.
Do not expose the receiver to high temperatures.
• The shrink cover could become distorted.
Do not break the tube.
• Could cause a short circuit.
When inserting and removing a connector, hold the
receiver tightly.
• Be careful so that a tube doesn't come off.
Please refer the table below for LED status vs
receiver's condition.
1M23N32102
R2001SB
Link switch
Antenna
S.BUS Port
CH3 output conventional system
/ Battery terminal
LED
S.BUS equipment
• Power requirement: 4.8V to 7.4V
• Battery F/S Voltage: 3.8V
* Be sure that when using ESC's regulated output the current capacity
of the ESC meets your usage condition.
* The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Bat-
tery F/S function doesn't work properly when a different type
of battery is used.
* The fail safe function can be set for each channel. However, it dif-
fers according to the transmitter. When you use TM-FH RF Module,
the fail safe function can be set for channel 3 only.
* S.BUS port: R2001SB can be used with up to 8 channels. However,
it differs according to the transmitter. An unused channel is a neutral
signal. The F/S setting channel at F/S is F/S position
.
Another, it is
Hold signal.
Direction of the connectors
90˚
Antenna installation
The power supply from S.BUS port is
also possible.
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba R2001SB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba R2001SB in de taal/talen: Engels als bijlage per email.

De handleiding is 0,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info