747922
34
Verklein
Vergroot
Pagina terug
1/183
Pagina verder
34
Before Use
Rubber
grommet
Brass eyelet
Wood screw
Servo mount
ŶƈƕƙƒŃƏƈƄƇŃƚƌƕƈƖŃ
To prevent the servo lead cable from being
broken by vibration during flight provide a
little slack in the cable and fasten it at suitable
points. Periodically check the cable during daily
maintenance.
Fasten about 5-10cm
from the servo outlet so
that the lead wire is neat
and secure.
Margin in the lead wire.
ŰƒƘƑƗƌƑƊŃƗƋƈŃƓƒƚƈƕŃƖƚƌƗƆƋŃ
:hen mounting a power switch to an
airframe make a rectangular hole that is a little
larger than the total stroke of the switch so
that you can turn the switch 21/2FF without
binding.
Avoid mounting the switch where it can be
covered by engine oil and dust. In general it is
recommended to mount the power switch on the
side of the fuselage that is opposite the mufÀer.
ŶƄƉƈƗƜŃƓƕƈƆƄƘƗƌƒƑƖŃƚƋƈƑŃ
ƜƒƘŃƌƑƖƗƄƏƏŃƕƈƆƈƌƙƈƕŃƄƑƇŃ
ƖƈƕƙƒƖő
WARNING
Connecting connectors
Be sure to insert the connector until it
stops at the deepest point.
How to protect the receiver from vibration
and water
Wrap the receiver with something
soft such as foam rubber to avoid
vibration. If there is a chance of
getting wet, put the receiver in a
waterproof bag or balloon.
Receiver's antenna
Never cut the receiver's antenna. Do
not bind the receiver's antenna with
the cables for servos.
Locate the receiver's antenna as far as
possible from metals or carbon fiber
components such as frames, cables,
etc.
*Cutting or binding the receiver's antenna will
reduce the radio reception sensitivity and range,
and may cause a crash.
Servo throw
Adjust your system so that pushrods
will not bind or sag when operating
the servos to the full extent.
*If excessive force is continuously applied to a ser-
vo, the servo could be damaged due to force on
the gear train and/or power consumption causing
rapid battery drain.
Mounting servos
Use a vibration-proof rubber (such as
rubber grommet) under a servo when
mounting the servo on a servo mount.
And be sure that the servo cases do
not touch directly to the metal parts
such as servo mount.
*If the servo case contacts the airframe directly,
vibration will travel to and possibly damage the
servo.
ŰƒƘƑƗƌƑƊŃƗƋƈŃŶƈƕƙƒŃ
Switch
Less than 5 mm of
mounting plate
Attached screw
Switch cover
34

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba FX36 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba FX36 in de taal/talen: Engels als bijlage per email.

De handleiding is 11,78 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Futaba FX36

Futaba FX36 Gebruiksaanwijzing - Deutsch - 61 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info